03-04-2007 03:35 AM
Dears;
I have 2811 router connected to the internet using ADSL connection;
i successfully configured the router to access the internet.
the image which router gas is c2800nm-ipbasek9-mz.124-4.
I need to configure the router to establish VPN tunnel.
which image should i installed .
Solved! Go to Solution.
03-04-2007 11:03 PM
Your HWIC-1ADSL is in the show diagnostics. According to this link it first support in 12.4(4)T http://www.cisco.com/en/US/products/ps5853/products_data_sheet0900aecd80394b7e.html
Use ADVANCED SECURITY 12.4(11)T with the filename c2800nm-advsecurityk9-mz.124-11.T1.bin (ED) instead
03-04-2007 04:47 AM
You mean IPSEC VPN?
Here are the IOS that supports IPSEC VPN for 2811, all of them requires 256MB DRAM and 64MB FLASH
Advance IP Services c2800nm-advipservicesk9-mz.124-13.bin
Advance Enterprise Services c2800nm-adventerprisek9-mz.124-13.bin
Advance Security c2800nm-advsecurityk9-mz.124-13.bin
03-04-2007 04:52 AM
Yes;
IPSEC VPN on 2811 which support ADSL.
Thanks
03-04-2007 07:52 AM
I think the image you have now supports IPSEC VPN. The K9 in the image name indicates that it supports IPSEC/3DES. Did you try configuring a VPN on it?
03-04-2007 08:09 AM
Yes;
and i am not able to find IPSec commands
03-04-2007 08:51 AM
Then you should try the advsecurityk9 feature set.
03-04-2007 12:51 PM
Dear;
i installed the image :
c2800nm-advsecurityk9-mz.124-13.
But i can't configure the ATM interface in my router?
i can't find the interface ATM command.
can you help me please.
03-04-2007 01:13 PM
when you do a "sh ver", can you see the interface listed?
Can you post your config?
03-04-2007 02:08 PM
Dear Sir;
previously i had the image:c2800nm-ipbasek9-mz.124-4.T.bin.
and successfully configured the ATM and dialer interface and connected to the internet.
but now i have to configured VPN Connection.
so i need to upgrade the image to security image so i can applied the commands.
but when i upgrade the image to c2800nm-advsecurityk9-mz.124-13.bin.
i can't find the ATM interface configuration.
I will send to you my run configurations.
03-04-2007 02:32 PM
Please check the following first:
-show version
Your ATM interface should be listed among the found interfaces.
-show interface
Your atm interface should be listed along with the ethernet interfaces.
If the ATM interface does not show up in either situation, you should check to the see if the card is correctly seated.
If it shows up in both commands, then you should be able to configure it.
03-04-2007 09:39 PM
Can you post the "show version" and "show diagnostic" output here?
03-04-2007 10:23 PM
ITS-BAH-OFFICE#sh ver
Cisco IOS Software, 2800 Software (C2800NM-ADVSECURITYK9-M), Version 12.4(13), )
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 22-Feb-07 15:39 by prod_rel_team
ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)
ITS-BAH-OFFICE uptime is 9 hours, 40 minutes
System returned to ROM by reload at 20:57:15 UTC Sun Mar 4 2007
System image file is "flash:c2800nm-advsecurityk9-mz.124-13.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.
Processor board ID FTX0925A5RP
2 FastEthernet interfaces
2 Virtual Private Network (VPN) Modules
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
03-04-2007 10:34 PM
Yeeesh, your ATM interface is not in the "show version". an you post the "show diagnostic" as well?
03-04-2007 10:37 PM
03-04-2007 10:52 PM
I thought you needed 12.4 T release to support HWIC-1ADSL Card. Your previous software must have been a 12.4(4T) or greater:
http://www.cisco.com/en/US/products/ps5853/products_data_sheet0900aecd80394b7e.html
WIC Slot 1:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 7.0
Top Assy. Part Number : 800-26247-01
Part Number : 73-9932-05
Board Revision : B0
Deviation Number : 0
Fab Version : 07
PCB Serial Number : FOC102207TV
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-1ADSL
Version Identifier : V01
CLEI Code : COUIADECAA
EEPROM format version 4
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: