Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

install "NM-1CE1T1PRI" on 2800

hi everybody

I have this module with 2811 router . I want to config e1 on it & the e1 line is up.but when I want to config it I enter to configure terminal mode , these is not card type e1 command .also, the card type & controller command are unrecognized commands for this router.

could you pls tell me what is the problem>

thanks

8 REPLIES

Re: install "NM-1CE1T1PRI" on 2800

First of all, you must determine if the module is recognized by the router. To do this, please upload the output of "sh ver".

It may also be that you see messages about unrecognized hardware at boot. If so, you might have the wrong software. I did not yet check if the combination is supported. I guess it is but with the requested output it will be possible to determine is this is the case or not.

Regards,

Leo

New Member

Re: install "NM-1CE1T1PRI" on 2800

yes when I check the show version command this is shown that the module is recognized with 1 port channelized e1 command. THe ios of this router is "c2800nm-ipbase-mz.123-8.T8.bin" that i sure this image support this module.what do you think?

Re: install "NM-1CE1T1PRI" on 2800

First of alkl you have to define the card type. Please check the URL below:

http://www.cisco.com/en/US/products/sw/iosswrel/ps5187/products_feature_guide09186a00801af22a.html#wp1027188

Regards,

Leo

New Member

Re: install "NM-1CE1T1PRI" on 2800

yes I want to set card type e1 1 command but the card type is unrecongnized for the router so, I can't set it & controller command?

this is my problem.

Re: install "NM-1CE1T1PRI" on 2800

It will be almost impossible to help you without seeing any output from the router.

Could you please post a screendump with the commands you tried and the subsequent error messages?

A sh ver could be very helpful as well.

Regards,

Leo

New Member

Re: install "NM-1CE1T1PRI" on 2800

Did the router recognize the card inserted? Is the card actualy in slot 1?

Please provide us at least with the output of show diag command.

New Member

Re: install "NM-1CE1T1PRI" on 2800

hi

the output of sho diag :

sho diag

Slot 0:

C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

PCB Serial Number : FOC10111UU7

Hardware Revision : 1.0

Top Assy. Part Number : 800-26920-01

Board Revision : A0

Deviation Number : 0

Fab Version : 03

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 87

Hardware date code : 20060316

Chassis Serial Number : FHK1012F1Y2

Chassis MAC Address : 0017.5a66.8cf8

MAC Address block size : 24

CLEI Code : CNMJ7P0BRB

Product (FRU) Number : CISCO2811

Part Number : 73-10258-03

Version Identifier : V02

--More-- EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF C1 8B 46 4F 43 31 30 31 31 31 55 55 37 40

0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 01 42 41 30

0x20: 88 00 00 00 00 02 03 03 00 81 00 00 00 00 04 00

0x30: 09 87 83 01 32 18 9C C2 8B 46 48 4B 31 30 31 32

0x40: 46 31 59 32 C3 06 00 17 5A 66 8C F8 43 00 18 C6

0x50: 8A 43 4E 4D 4A 37 50 30 42 52 42 CB 8F 43 49 53

0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12

0x70: 03 89 56 30 32 20 D9 02 40 C1 FF FF FF FF FF FF

Slot 1:

NM-1CE1T1_PRI Port adapter, 1 port

Port adapter is disabled

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.0

Top Assy. Part Number : 800-21550-01

Board Revision : E0

Deviation Number : 0-0

Fab Version : 03

PCB Serial Number : FOC0809W0O7

RMA Test History : 00

--More-- RMA Number : 0-0-0-0

RMA History : 00

Fab Part Number : 28-5935-03

Manufacturing Test Data : 00 00 00 00 00 00 00 00

Field Diagnostics Data : 00 00 00 00 00 00 00 00

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 9D 41 01 00 C0 46 03 20 00 54 2E 01

0x10: 42 45 30 80 00 00 00 00 02 03 C1 8B 46 4F 43 30

0x20: 38 30 39 57 30 4F 37 03 00 81 00 00 00 00 04 00

0x30: 85 1C 17 2F 03 C4 08 00 00 00 00 00 00 00 00 C5

0x40: 08 00 00 00 00 00 00 00 00 FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Router#

New Member

Re: install "NM-1CE1T1PRI" on 2800

I'd try the interactive setup process

Router# setup

The first question appeared would be about E1/T1 configuration. If it wouldn't consider to upgrade your IOS.

185
Views
0
Helpful
8
Replies
CreatePlease to create content