Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

NM-12DM and 3825

Hello all!!!

I try do use this configuration:

CISCO3825

NM-8B-S/T

NM-12DM-RF

But just NM-12DM-RF installed router does not boot..

The output of console attached later...

What should I do to this configuration work fine?

Does this configuration correct?

May be I should update (or downgrade) IOS?

Thank you very much...

System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2006 by cisco Systems, Inc.

Total memory size = 256 MB - DIMM0 = 256 MB, DIMM1 = 0 MB

c3825 platform with 262144 Kbytes of main memory

Main memory is configured to 72/0(dimm 0/1) bit mode with ECC enabled

Readonly ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xcb40

program load complete, entry point: 0x8000f000, size: 0xcb40

program load complete, entry point: 0x80010000, size: 0x225d4a8

Self decompressing the image : ################################################################################################################################################################################################################################################################################################################################################################################################### [OK]

Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

00042A 0X010D78F3 C3825 motherboard

000021 0X00085200 Eight port Multi-BRI

000067 0X0001CF20 Digital Modem Module

0X00288860 Onboard PVDM2 SIMM

0X000021B8 Onboard USB

0X00660670 public buffer pools

0X0078F000 public particle pools

TOTAL: 0X021F3A9B

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 34Mb.

Using 13 percent iomem. [34Mb/256Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, 3800 Software (C3825-SPSERVICESK9-M), Version 12.4(6)XE3, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Tue 07-Aug-07 23:31 by prod_rel_team

Image text-base: 0x60011084, data-base: 0x62D38A00

System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2006 by cisco Systems, Inc.

*** Watch Dog Timeout Reset ***

ra = 0x603906a4, EPC = 0x608989b8

*** BCM 1125 went through a full reset. HT/PCI fabric reset. ***

Total memory size = 256 MB - DIMM0 = 256 MB, DIMM1 = 0 MB

c3825 platform with 262144 Kbytes of main memory

Main memory is configured to 72/0(dimm 0/1) bit mode with ECC enabled

3 REPLIES
Hall of Fame Super Gold

Re: NM-12DM and 3825

Hi,

first of all, you cannot use the NM-8B-S/T to access the Digital Modems, please see:

http://cisco.com/en/US/products/ps6441/products_feature_guide09186a00806b941f.html

In any case, you need 12.4(9)T or later for the Digital Modems.

Hope this helps, please rate post if it does!

Community Member

Re: NM-12DM and 3825

oh, oh, oh...

You right, but I don't use any PVDM2-XXDM modem.

I try to use old EoS hardware modem NM-12DM-RF.

This hardware can work fine with NM-8B-S/T...

But I have trouble with NM-12DM-RF and 3825...

This module (NM) does not work fine with 3825...

What should I do?

Thank you for your opinion...

Hall of Fame Super Gold

Re: NM-12DM and 3825

No, you're right, because I don't read properly (sometime one only read what he wants to). Sorry for the confusion.

I think you're in the right to open a case with the tac so they can reproduce the problem. This document:

http://cisco.com/en/US/prod/collateral/routers/ps5855/prod_qas0900aecd8016a953.html

Clearly state that despite being EoL, both network modules are supposed to work on the 3800. Then perhaps they just don't :(

917
Views
0
Helpful
3
Replies
CreatePlease to create content