Hello,
is this the entire configuration ? Have a look at this sample configuration:
!
boot-start-marker
boot-end-marker
!
enable secret 5 XXXXXXXXXXXXXXXXXXXXXXX
!
username root privilege 15 password 7 XXXXXXXXXXXXXXXXXXXXXX
no aaa new-model
ip subnet-zero
no ip domain lookup
!
ip host Router1 2001 172.16.1.1
ip host Router2 2002 172.16.1.1
ip host Router3 2003 172.16.1.1
ip host Router4 2004 172.16.1.1
ip host Router5 2005 172.16.1.1
ip host Router6 2006 172.16.1.1
ip host Router7 2007 172.16.1.1
ip host Router8 2008 172.16.1.1
ip host Router9 2009 172.16.1.1
ip host Router10 2010 172.16.1.1
ip host Router11 2011 172.16.1.1
ip host Router12 2012 172.16.1.1
ip host Router13 2013 172.16.1.1
ip host Router14 2014 172.16.1.1
ip host Router15 2015 172.16.1.1
ip host Router16 2016 172.16.1.1
!
interface Loopback1
ip address 172.16.1.1 255.255.255.255
!
interface Ethernet0/0
ip address 192.168.100.90 255.255.255.0
half-duplex
!
interface Ethernet0/1
no ip address
half-duplex
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.100.1
ip http server
!
line con 0
line 1
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 2
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 3
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 4
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 5
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 6
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 7
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 8
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 9
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 10
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 11
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
speed 38400
line 12
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 13
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 14
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 15
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line 16
session-timeout 30
exec-timeout 0 0
no exec
transport input telnet
line aux 0
line vty 0 4
exec-timeout 60 0
login local
!
end
The line numbering depends on the slot in which the module is inserted, Slot 0 has line numbers 0 thru 32, Slot 1 line numbers 33 thru 65, etc...
In the above example, the module is installed in slot 0.
The third section of each command contains the port number for the devices, and the last two digits of the number designate the port. For example, 2001 follows the first router ("Router1"), meaning this router is on port 1. The last part of the command contains the IP address of the Ethernet port on the console server.
By creating these names, you don't need to know which port the device is on. All you need to do is Telnet to the host (in this case, Router1) off of the console server.
You could also reach this device directly from a PC. For example, you could Telnet to 172.16.1.1 2016 from your PC. This tells the Telnet client to go to port 2016 instead of the default Telnet port 23.
HTH,
Nethelper
