Routers - Small Business

Hi all please help me I have WRVS4400N V2 FW Version:V2.0.2.1in gateway mod with one public addressAnd a lots of questions : For what is necessary VLAN interrouting ? At which nivel is routing ? if at the IP nivel ?ACL :I have an architecture like th...

Hello, first time Cisco user here.I just purchased an RVS4000 and would like to know (if I can and how to setup) this as a VPN device solely, or do I have to put it in front of my existing router/gateway (with proper port forwarding, of course).  I'm...

Last day I bought this router but i have a problem. I create a vpn user then i generate certificate, export client certificate and copy to the remote PC in the directory C:\Program Files\Cisco Small Business\QuickVPN Client. When I try to connect, Qu...

I am considering purchasing a SRP547W Router but there are a couple of things that I am trying to clear up before I do.I am hoping that someone here can assist with the following questions:I want to do load balancing using two WAN connections (ADSL2+...

I am trying to open port 554 or set up an RTSP and i am totally lost.I am trying to set up remote monitoring for my store camera system and we got a new dvr. Any Help would be greatly appreciated

I don't know if this is possible at all - so would be very thankful to get a "high-level" answer.  But, any answer will do!! First, to set the stage, I'm going to assume that there is a private or leased line connecting two sites.  Those sites are co...

Good Morning, Yes I know its Sunday, have been trying with this issue for the last month and came to the Community for much needed help or a little guidance if possible.Previous Scenario:ZHONE 6218-I2 aDSL Router with dynamic ip from Telecom Provider...

I'm using ProtectLink on my RV220W, and since activating, my TiVos are unable to connect to the mothership to get program data (fails at negotiation). I've tried to isolate it to a given setting, but if any single ProtectLink option is enabled, be it...

Hello,We've just bought a SA540 router/firewall.I've made a basic configuration for the begining by connecting my laptop directly to port1.ADSL Internet connection is on WAN port and a switch (LinkSys) on port 1.It wa sworking during few hours and no...

Hi,Does the RVL200 offer Port Address Translation and it so where do I find the feature in the web interface. So far I have only found Port Forwarding and Port Triggering. The RVL200 has got the latest firmware installed (1.1.12.1).Thankyou,Robin Hor...

Environment: RV042 V03 (firmware v4.0.0.07-tm) currently routing a /29 to an internal network.We used up our /29 and now have a 2nd non-contiguous /29.  Both of these come over the same wire.Is there any way to configure the RV042 to route both block...

I have problem with RV110W and QuickVPN when second client within same network behind NAT wants to connect remote RV110W by QuickVPN. The first client connects correctly (eg. 213.220.226.145[192.168.2.230]), the second one (eg. 213.220.226.145[192.16...

Hi, i have the Protectlink service and i just received a mandatory upgrade firmware from the immediately previous firmware where everything worked and now with update WAN access is blocked. Access log is attached. Revert to previous version firmware ...

Good day.I just installed one RV220W in my network, in routing mode (not NAT) using on WAN port public Ip 193.111.184.xxx and on LAN side on IP from my company public C class (212.100.143.0). It's working, but main ang huge problem is than Router is ...

Firmware Release        v2.0.0.8IPS Signatures            1.42ProtectLink                 Not ActivatedLog Level Enabled to    0,1,2Outgoing Log               DisabledIncoming Log               DisabledLoccal Log                  DisabledE-Mail Alert...