cancelar
Mostrando los resultados de 
Buscar en lugar de 
Quiere decir: 
cancel
672
Visitas
0
ÚTIL
1
Respuestas

WS-F6700-DFC3CXL // CISCO7604 (R7000) // WS-X6704-10GE

martcorrea
Level 1
Level 1
Hola.
Buenas tardes.
Tengo un equipo 7604 con una tarjeta WS-X6704-10GE, insertada en el modulo 4, pero en el show module recibo el error PwrDown en el status. 
Actualmente esta corriendo con la versión de IOS c7600s72033-advipservicesk9-mz.122-33.SRD8.bin en las dos supervisoras.
¿Me podrían ayudar para saber cual es la causa por la que no reconoce esta tarjeta?
570l2lDFrtr7604-02#sh module
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1    2  Supervisor Engine 720 (Active)         WS-SUP720-3B      
  2    2  Supervisor Engine 720 (Warm)           WS-SUP720-3B      
  3   40  7600 ES+                               7600-ES+40G3CXL    
  4    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE    
 
Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  1  001e.be6e.d574 to 001e.be6e.d577   5.7   8.5(2)       12.2(33)SRD8 Ok
  2  001e.be6e.d570 to 001e.be6e.d573   5.7   8.5(2)       12.2(33)SRD8 Ok
  3  30f7.0d8d.8350 to 30f7.0d8d.83af   1.6   12.2(33r)SRD 12.2(33)SRD8 Ok
  4  0024.145f.1fa0 to 0024.145f.1fa3   2.7   Unknown      Unknown      PwrDown
 
Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
  1  Policy Feature Card 3       WS-F6K-PFC3B         2.4    Ok
  1  MSFC3 Daughterboard         WS-SUP720            3.2    Ok
  2  Policy Feature Card 3       WS-F6K-PFC3B      2.4    Ok
  2  MSFC3 Daughterboard         WS-SUP720            3.2    Ok
  3  7600 ES+ DFC XL             7600-ES+3CXL         1.3    Ok
  3  7600 ES+ 40xGE SFP          7600-ES+40G        1.3    Ok
  4  Distributed Forwarding Card WS-F6700-DFC3CXL     1.2    PwrDown
 
Mod  Online Diag Status
---- -------------------
  1  Pass
  2  Pass
  3  Pass
  4  Not Applicable
570l2lDFrtr7604-02#sh power
system power redundancy mode = redundant
system power total = 2669.10 Watts (63.55 Amps @ 42V)
system power used = 1040.76 Watts (24.78 Amps @ 42V)
system power available = 1628.34 Watts (38.77 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 PWR-2700-AC/4 2669.10 63.55 OK OK on
2 PWR-2700-AC/4 2669.10 63.55 OK OK on
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 FAN-MOD-4HS 57.54 1.37 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 WS-SUP720-3B 282.24 6.72 282.24 6.72 on on
2 WS-SUP720-3B 282.24 6.72 282.24 6.72 on on
3 7600-ES+40G3CXL 418.74 9.97 418.74 9.97 on on
4 WS-X6704-10GE 362.46 8.63 - - on off (Module Failed SCP dnld)
Saludos,
1 RESPUESTA 1

Ricardo Prado Rueda
Cisco Employee
Cisco Employee

¡Hola!

   Tu tarjeta está teniendo problemas de comunicación con la supervisora del equipo. Podrías intentar remover la tarjeta del chassis y volverla a insertar a ver si esa era la causa. También podrías intercambiar las tarjetas de los módulos 3 y 4 para ver si el problema sigue a la tarjeta o al módulo. En caso de que siempre sea esa misma tarjeta la que se apaga por este problema de comunicación tendrías que reemplazarla.

Saludos.