Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Start a conversation

Resolved! BGP Outbound traffic preferencein multihomed traffic

Situation 1: I have two edge routers each talking EBGP ( ISP -1 and ISP-2) to a different service provider and talking IBGP to each other. i'm  receiving full internet routes from both providers. In this situation each edge router will have to decide...

viswa sai by • Level 1
  • 2243 Views
  • 12 replies
  • 0 Helpful votes

Resolved! vlan with site-to-site VPN - asa to azure

At the office we have the following setup: MD-Office LAN- 172.28.0.0/22 - MD-Inside interface - Security level 100 MD-Office-Prod VLAN - 172.28.4.0/24 - MD-Inside-Prod virtual interface - Security level 100 "Enable traffic between interfaces with sa...

BFD State Bit is Admin Down

Hi, I am facing the issue with BFD on ASR 903 router where State bit is showing : AdminDown and also Rx count is 0. Any reason why state bit in admin down and how to resolve this particular issue. Logs BOTDBTDGPAR001#sh bfd neighbors interface bd...

visehgal by • Level 1
  • 3292 Views
  • 0 replies
  • 0 Helpful votes

BGP Configuration & Failover

Hello All, We have two links from two different ISPs on BGP. Both links are connected on different CE router at our end. Network diagram attached for reference. We are advertising two pools on this links , 192.168.10.0/24 from one ISP and 192.168.30...

keen4.net by • Level 1
  • 7703 Views
  • 8 replies
  • 0 Helpful votes

Unable to access NAT devices on Cisco 891F

Hello, I was changing my configuration for my router and somehow messed up the NAT translation.  Previously it was working.  I should have made a backup config.  However, now I cannot access any devices on my internal network setup with NAT from the...

High CPU utilization on C6509 with VS-SUP2T-10G

Hi, I have a 6509-E chassis deployed as WAN termination router, only having the following links connected to it :- 3 port etherchannel connecting to ISP for 3gig uplink (ports Gi1/1-3)Downlink-1 1gig (Gi2/1)Downlink-2 1gig (Gi2/3)Downlink-3 1gig (Gi...

bhushit17 by • Level 1
  • 3164 Views
  • 12 replies
  • 0 Helpful votes

internet fail over issue

Dear Expert, Hope you are doing well ! i  have two firewall 5512 and 5506 at main site and non main site respectively.for main site has 3750 switch which is connected to firewall(5512) and firewall connection goes to ISP directly and same situation o...

mpate1311 by • Level 1
  • 185 Views
  • 1 replies
  • 0 Helpful votes

dual hub dual spoke dmvpn

Hi ,we have main office with remote office with DMVPN connection ,in office there we use OSFP protocol ,with remote office we are using eigrp and with redistributing we solve the connectivity.Now customer has bought 2 routers ,one for remote office a...

Resolved! Best way to migrate

Hi, I currently have 2 cisco 3750X stacked switches and I need to replace them with 2 new cisco 3850 switches.  What is the easiest way to accomplish this?  I thought of configuring the 3850 stack with basics, then connect to the 3750 to pass vlans....

Slow VPN Throughput

I have two sites linked with a basic IPSEC tunnel between them. I am struggling to get any more than 10MB across the VPN. Site 1 has a 50MB LL and site 2 Is in a Data Centre with a 1GB Max connection. Both routers are Cisco 1841 routers with VPN card...

Resolved! Recursive Lookup?

Hi All ,   Could you all let me know what is Recursive Lookup.   I just want to know it without any regards to any protocol.   As per my understanding :   Routing table for R2:   C - 10.0.0.0/24 -> S3C - 10.0.1.0/24 -> S2C - 10.0.2.0/24 -> S0C - 10.0...

NAT Translation Failed

Dear, We face problem in our network, NAT translation failed and we don't have internet access when this problem occure. How we can fix this issue. Running Configs and Logs here,  Interface and Nat Configurations, interface GigabitEthernet0/0.1659 d...

View All
Review Cisco Networking products for a $25 gift card