Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Start a conversation

Errors on a 2801 Router

Client has a C2801 router with the following interfaces:2 FastEthernet interfaces2 ISDN Basic Rate interfaces2 ATM interfaces1 terminal line1 Virtual Private Network (VPN) Module1 DSP, 8 Voice resources1 cisco service engine(s) Client is constantly h...

jonl711 by • Level 1
  • 475 Views
  • 1 replies
  • 0 Helpful votes

RPS2300 cable for 2911 / 2921 router

Hi,When I read the literature I come to the conclusion that I need the CAB-RPS2300= 14 pin connector. But when I look at the installation documentation it shows a 22 pin connector on the router.I therefpre should order the CAB-RPS2300-E=.correct?Robe...

rosuares by • Level 1
  • 2669 Views
  • 2 replies
  • 1 Helpful votes

Cisco 887VA Install support?

If I just purchased a Cisco887VA-SEC-K9Call I call Cisco and they can help me set it up?I am trying to replace a PK5000 in "Block of static mode" but I am fairly new to the world of Cisco.I used to work with 678's 10 years ago.Thanks. 

priority class traffic gets dropped

Dear fellow Ciscoers,I've been wondering if I may have missed something in my config and could use a second pair of eyes. I am configuring a router for a branch office that will connect to head office via VPN and created a policy for a bunch of VOIP ...

mhattar by • Level 1
  • 398 Views
  • 2 replies
  • 0 Helpful votes

Resolved! ACL to allow SNMP traffic

I created an ACL to allow SNMP traffic through.  Once I applied it traffic does not pass.  Should be pretty simple.  Below is what I used.  I am using SNMP v2.ip access-list extended ABC-ACL permit udp X.X.0.0 0.0.255.255 host SERVER_IP eq snmp permi...

HMidkiff by • Level 1
  • 59996 Views
  • 7 replies
  • 0 Helpful votes

Resolved! EIGRP

Gentlemen,I am planning to change the Subnet id /Mask of one of our back up router's interface and I was wondering if that could have any negative impact on EIGRP route and its convergence and if it could stop advertising static routes to other route...

Resolved! Voice VLAN - CDP role

Hi All, Though it is basics, I am confused a little to understand the VOICE VLAN. Can you help me to get insight on the belowThere is a IP Phone and a PC is connected to the Phone    interface GigabitEthernet1/0/12    description **** Cisco IP Phone ...

Router sizing

Need to select a router that can support upto 30 OSPF stub areas, with 3 or 4 routers in each stub areaAny advice gratefully recieved and how you calculated your answer . Cheers 

r-godden by • Level 1
  • 422 Views
  • 2 replies
  • 0 Helpful votes

Incoming NAT query - Diagram

With a setup similar to the diagram - If I have multiple NATs configured on each device, using multiple IPs. When traffic comes in from the ISP looking for say 1.1.1.10 /24 I'm guessing the Firewall Outside Interface is aware of this IP being used in...

GRANT3779 by • Spotlight
  • 179 Views
  • 1 replies
  • 0 Helpful votes

Resolved! second IP address

HelloI need to change the IP's on several switches and routers.  What is the correct procedure for adding a second IP and then removing the old one.  I will need to do most of this remotely so I cant loose access to the equipment.

When to use a GRE Tunnel?

I'm a little confused when to use a GRE tunnel and when to just use a simple VPN with IPSec tunnel.For example, I have a development network (192.168.0.0/24) that I need to encrypt the traffic using IPSec, then tranport it over a 10.0.0.0/24 network....

View All
Review Cisco Networking products for a $25 gift card