Resolved! Reset to factory default
Found the solution, the device was broken and I just returned for different unit.
Found the solution, the device was broken and I just returned for different unit.
Today, one of our 3750 switch stack member went for reboot. On log:000013: *Mar 8 05:55:27.663: %PLATFORM-1-CRASHED: System previously crashed with the following message: (switch3750MARWARI-2)000014: *Mar 8 05:55:27.663: %PLATFORM-1-CRASHED: Cisco ...
i just got a used cisco 877 from ebay, the router i got not reponding to ping, and not picking up adsl signal, i ask the seller for a refund, the seller told me i must use aux cable to program, i had a cisco 857, which can be program through etherne...
Hello experts!I have a question. One of our clients has this in all their core switches and it happens constantly. This probably started about 3 months ago. Is this stating that the interface is going up and down?Jun 7 2012 07:18:11 PST-ST: %DUAL-5-...
Hi Expertshow to configure 1900 router for local AAA and only allow ssh to it thanksjamil
Hi , a have a design problem . I have a datacenter and i want to provide point 2 point VPN for clients to their servers. I don`t want to purchase for any new client a new router to separate each client. What device and what type on VPN is going to su...
hi expertsi have servers in dmz starts with 172.x.x.x and servers in inside starts with 192.168.x.x , i have tried to implement RFC1918 to on my border router connected to isp , i have applied the acl (IN Direction) on inside interface then all the ...
Hy guys,I'm having trouble with an ASR 1002 router. The WAN connection never exceeds the 196/255 on txload, and at this point the taildrops becomes a real problem. There is no QOS configured. The remaining 25% of the bandwidth is sealed for some rea...
HIthink everyone know without me. Traditionaly in datacenter Server connect with LAN switch and SAN Switch by ( LAN card and HBA card)and from San Switch another fiber connectivity with SAN.Now I heard Cisco come with Nexsus switch whcich reduses cab...
Say I have a network 10.10.10.64 /29...what should my "network" statement look like in a RIP v2 configuration?network 10.10.10.64right?
Guys,I have a 2800 with one Gigabit interface connection to our Lan and the other interface connected to the internet with a public IP address. Now I'd like to setup the router to resolve both internal and external DNS requests. Thus requests like ww...
The basic setup... Newly installed redundant ISP, thus setting up the 891 with dual WAN, Using PfR to load balance between the two. Did initial config through CCP (not express), but I am familiar with the basics of IOS CLI (not used to the new zone b...
Hi ,i am using cisco 2821 router at the edge in my network where the WAN link is terminated.i want to configure Redundancy . So will 2821 support ? If yes what is the another router .Is it the same series or different for redundant configurati...
Hi Everyone,I have a cisco router and I'd like to set it up so my PCs can get the internet from it but it doesn't seem to work for me.From router CLI, I can ping 4.2.2.2 and other IP addresses but my PC which connected to int fa3 can't access to the ...
Current Set up============Primary router R1 is connected to MPLS cloudBackup router R2 is connected to MPLS cloudBoth primary and backup link have same bandwidthFor incoming traffic primary link in R1 is preferred because of best AS-PathBackup link i...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 03:04 PM | ||
04-26-2024 01:23 PM | ||
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |