Guysworking on the 3725 with advanced IPS image,I am looking for PHDF File to be load to flash,pls post me the direct link to download it .... i didn;t find itThanks
Guysworking on the 3725 with advanced IPS image,I am looking for PHDF File to be load to flash,pls post me the direct link to download it .... i didn;t find itThanks
Hi,Which router is better 891 or 892, what is the difference between them and which one is cheaper and by how much ?My requirement is to run about 10-20 computers from each router.Regards,Mero
Hi Guys,Im trying to setup a static nat for a branch site so that any packets that come in over the WAN with the destination 192.168.25.148 are translated to 172.18.84.11. Any traffic with the destination of 172.18.84.11 should stay untouched.I've ...
Is it possible to redistribute a static route into EIGRP and make it appear as Internal EIGRP route instead of External EIGRP route ?
Hello,I'm currently mulling over the concept of running a full BGP table (340000 prefixes more or less) inside a VRF or whether I should stick with the normal and just use the Default IP Routing Table and VRF everything else....Can't make my mind up,...
Hi.I want to purchase a uc540w for a small office (with IPSec and IPS) to use as a router , firewall and for IP phone management. The problem Is there Is a DSL line for data and a seperate DSL line for voice.How can I route the data and voice to the...
Hi allAmongst other things, I'm trying to get two Cisco 1941 routers with HWIC-1T and HWIC-3G-HSPA interfaces to use the 3G interfaces if the frame is down (as it is right now).In the lab, I was not able to get these to use the 3G interfaces as a bac...
I recently upgraded my 2811 router with an AC-IP power supply, and installed a HWIC-4ESW-POE, with an Inline Power Daughter Card (ILPM-4) installed on the HWIC.The second I turned the router's power on, there was a spark and a burning smell. Everythi...
Hi ExpertsPlease find attachmentHave you seen this type of setup before?what is the pros and cons of this topologythanksIbrahim
Hello,We have 50 Mb Comcast cable conencted to 2951. There is another conenction to AT&T 20 Mb circuit which goes thru' an ASA 5510. Path to Internet is as below.3750 Stack------Barracuda---------2951------------Comcast ...
Hi allI have two 1941 routers both with HWIC-1T and HWIC-3G-HSPA interfaces.I set these up to talk over frame relay in a lab using a cross over cable. Once I got this working, the routers were shipped to their respective homes, about 100km apart and...
Hi Expertswhat is the ospf cost for 1G and FE, if i need to adjust cost per interface not under the ospf processwhat is the impact of routing if we didnt tune the ospf cost ,as i know the default ospf cost is 100Mbps, while we have 1G in our network...
Hello all,I've got a situation where I want to conditionally advertise a prefix via BGP when any 32 bit route exists for the given prefix. E.g. I only want to advertise prefix 198.168.1.0/24 if a /32 exists for this network, so say 192.168.1.1/32 or ...
Hi all,Let's say I have two routers (RouterA will be .5 and RouterB will be .6) with a virtual GLBP address of .1Is it possible to have some hosts on that subnet bypass the GLBP protocol by setting their default gateway to the .5 or 6. address?
I want to connect my clients from the Windows WS to a VPN Tunnel using 3925 router w/o Cisco VPN client. Is there the way to use native IPSec client on Windows XP or Windows 7?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM | ||
04-24-2024 03:57 AM | ||
04-23-2024 05:38 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |