I would like to know command which show any protocol on that interface (same as "ip cache-flow) of GSR 12000 with XR OS.
I would like to know command which show any protocol on that interface (same as "ip cache-flow) of GSR 12000 with XR OS.
Hello, I'm losing access to the GSR either by console or SSH. Cisco recomenden moving from IOS XR version 3.8.2 to version 3.9.2 after the upgrade we are still getting the same behaviour.Has anyone had the same problem?Best,Jose
Please i need help configuring the frame relay switch "FRS",Here is the configuration on R1, R2 and R3:R1:interface Loopback1ip address 10.1.1.1 255.255.255.0!interface Loopback2ip address 10.1.2.1 255.255.255.0!interface Loopback3ip address 10.1.3.1...
Dear All,We want to implement redundancy for our LAN-to-WAN connectivity. There are 2 redundant L3 swithches running HSRP connected to the LAN, and there is a single WAN router(7206 VXR, with NPE-G1). The WAN router is connected only one L3 switc...
Hello Experts,I am running into issues with high CPU ( 90-95% ) on Cisco 7204 vxr with NPE G 1 ( 1gb dram ) , The router has around 100 GRE tunnels ( no ipsec protection ) , and there is constant 100 mbps traffic inbound & outbound , all through the ...
Hi all,I got a little problem when configuring a switch Cisco Catalyst 3750. Maybe, it is a kind of easy for you guys, but I couldn't do it. So, I'm asking from you.Here is my problem. There are two vlans on the switch. Vlan 1 is connected to interne...
I have 1841 router, SDM is installed but FA 0/0 is connected to ISP modem, and FA 0/1 is connected to intern/w through a linksys switch, given ip address as per the interfacesInterface IP-Address OK? Method Statu...
Dear All, I have an odd case please see the diagram link below, i need reach from R-C01 (192.168.253.0/24) to 192.168.90.0/24 load balance or load sharing via R-BH-01 and RR01 is it posible ? how to configure it?
Dear Team,we have a problem in routing between primary and secondary links.we have a two office and we are connected with intranet 2 Mb and we have configured back-up Site-Site VPN on firewall for remote office.Now the problem is when the primary is...
How does one identify what the default route is using ospf?I added it with two different commands and there is no indication what interface or network is the default route.see attachthx
I've never setup a DSL connection before so I'm looking for help on things I may have missed. If you see anything in my config, let me know. I'm not sure about my NAT commands.DSL modem is 192.168.1.254Cisco 871 router is 192.168.1.250LAN DC server i...
Hi,I have a couple of hosts on a remote network which are infected with a Trojan and various other malware. The hosts themselves are on a DHCP network and I would like to block access from these hosts using a MAC filter.Is this possible on 12.4(24)T2...
I am interested in a Cisco 1941W or 1941 specs state it has 2 x Onboard LAN 10/100/1000. The datasheet sheet calls them WAN then LAN ports. I've seen the Cisco Router performance PDF which states this model does upto 25Mbps throughput. Does this mea...
HelloCould someone help me with an extended access list that I try to figure out.I want my router to only accept various /16 prefixes and deny everything that is greater than /16.Right now i get these networks: 192.12.0.0/16 192.13.0.0/16 1...
Doing a large multicast qos setup for a client using a video content server to push to remote sites. The question I have is about the QoS. I started to setup a QoS policy with that multicast stream address and realized that multicast is an egress t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM | ||
04-24-2024 03:57 AM | ||
04-23-2024 05:38 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |