Routing

We have a 6509 and need to configure WCCP ver 2 (need it for video / https etc). My questions are- does WCCP work if we have vrf's on the 6509 / network?- if a certain entity only needs http (version 1) how will this affect them if we use ver 2versio...

Hi;Although we successfully configured and run wccp version 1 on cisco 6500 (sup 720, ios ver : 12.2.(33) SXH), we couldnt be able to with wccp version 2. We see the redirected packets on 6500 but no one going out net.We want to use https redirection...

All,I have a downstream customer who has requested that we implement communities. We've never had a request for them so we just never set them up... He is multi-homed. one connection to us and one connection to Provider X.As I see it, I can provide h...

I am hoping you all can help me figure out the best way to do this:We have 2 locations that are connected across a p2p t1 and Location 2 comes back to location 1 for internet access.We have wifi networks setup at both locations for internal use.  We ...

Hi,I have a c831 router that is having a few problems rebooting itself.  So had another 831 that I was not using so I copied the startup-config from the failing device to the other and swapped them out.  Most everything seems to work except I have a ...

When I execute the reload command on my 2811 it loads the correct bin file based on my startup config (see below), however the rest of my config doesn't load.     boot-start-marker     boot system flash:c2800nm-advsecurityk9-mz.124-24.T2.bin     boot...

HiLooking at the BGP Cost Community, I keep reading about how this influences the BGP best path selection process at the point of insertion (POI). Does this mean that the decision is taken immediately after step 8 in the Best Path Algorithm - ie Pre...

We have a router (ROUTER1) that is managed by our software provider that creates a site to site VPNconnection. The router has an internal and external IP and we have the external address setup in BGPas a network. This setup allows us to provide onlin...

I am attempting to establish a site-to-site tunnel between an ASA 5505 device and a Cisco 2811 Router. I can get the tunnel established successfully, but have no connectitivy between the two inside LAN's. If I attempt to ping from one LAN to another,...

Hello,we are using Catalist 3550 with L3 Image as Core BGP router for one AS. It is not a Full BGP router, in memory are only routes from our IX - interface exchange centre. Just a few.My question is:Is possible to add next AS to this device? Does it...

My customer has a Hoot n Holler application on their entreprise that consists of 7936s plugged into fxs ports which PLAR to a VoIP dial-peer with "session protocol multicast" and that, of course, gets multicast around the enterprise.So my challenge i...

thanks for your helping. what is the problem?CISCO2811, Integrated Services Router 2xFE, 4 WAN slots, 128 FL/512 DR (default specs)they have default specifications like that, the router are fully new.after the router is powered on, the cursor is fla...

Hello I have a problem with GW I get this mesage:Oct 18 17:24:29.389: %PQUICC_ETHER-3-UNDERFLO: Unit 0, underflow errorOct 19 19:37:01.373: %TCP-2-BADREFCNT: Tty0: Bad refcnt for packet 0x83E5FF80 during retransmit, 10.100.2.253(46158) to 180.33.186....

Hi,I have three Cisco 887 routers (adsl) connected to the Internet and connected to each other via site-to-site tunnels.We run voice SIP, RDP (remote desk top protocol), we want to stop Internet and site-to-site downloads interfering with voice and R...