Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Hi,Wanted to know how much HWIC card we can have in 1841 modular router.Presently we are using 2 FE and 4 Serial interfaces.I don't have the physical access of the router but do have sh tech with me.I assume all slots are occupied and nothing can be ...

sushil by Level 1
  • 714 Views
  • 1 replies
  • 0 Helpful votes

HiIs it possible to set the following command on a Cisco 877 Routerrouter bgp 65500At the moment it is saying it doesnt recognize the command and when I do router ? I don't see it in my list.Thanks!

I already install new ios on my 2950 switch but when i boot switch from new ios it gives a error message permission denied and boots fromold ios what can i do now to resolves this issue

Hello CSC,I have a routing problem that has been plaguing me for several months now. About 5-6 months ago we upgraded our remote sites to MPLS. After the upgrade we decided to keep the point to point T1’s circuits in place to provide redundancy inca...

Resolved! HWIC-1FE

Hi there,Cisco documents shown that Cisco 3845 able to support HWIC-1FE with certain minimum IOS version, but why when I slot in the card, its show the following???  Thanks for the help. WIC Slot 0:        Unknown WAN daughter card        WIC module ...

I noticed that there is a release note on site for QuickVPN 1.4.1.2 dated July 21 but I have been unable to find the download. Any pointers would be appreciated. I'm having the well reported issue with vista connect timing out.Ted

ted-quade by Level 1
  • 2815 Views
  • 2 replies
  • 0 Helpful votes

Resolved! eBGP or iBGP

Hi, i have one part of my network on my building on the other part on a datacenter.I have a point to point link between the two sites. I know i must use BGP for redondancy but what BGP the eBPG or iBGP?I attach a schema.For me i must eBGP between the...

hi everyone,i was setting this ospf lab and as we all know distribute lists only removes LSAs from the router that has the DL on it but it still passes LSA to other routers and they do install this routes in their routing table..here's the scenario, ...

hamalawy1 by Level 1
  • 1402 Views
  • 2 replies
  • 0 Helpful votes

I have what i think to be a routing question. Below is an what i see to be the problem.The networkMPLS (to remote site)                                       Firewall Cisco ASA 5510 (Between Network and Metro E)172.16.1.1                             ...

sbohannan by Level 1
  • 1043 Views
  • 6 replies
  • 0 Helpful votes

Hi!I wonder why I get such a route on my ABR:O*E1 0.0.0.0/0 [110/10067] via 10.47.0.7, 00:05:52, Serial0/0This router is connected to backbone area and area 1. Serial 0/0 is assigned to area 1 nssa only.Also, do I have to have only one exit to the ba...

ropakalns by Level 1
  • 1194 Views
  • 6 replies
  • 0 Helpful votes

HiI have a an EZVPN Server with static IP  address and unfortunately, EZVPN Remote clients(network extension) that  will have dynamic IP addresseses.Everything is working now.EZVPN Server is on Site_AEZVPN Remote Site (Dynamic IP ) is Site_Bshow cryp...

HelloI am looking for help in securing the VPN Box by allowing only VPN Trafficrest all internet traffic should be blocked.here is the configuration, can someone input.###VPN Router###crypto isakmp policy 1 encr 3des hash md5 authentication pre-share...