Routing

In a lab MPLS configuration, I have a PE1 router connected to External BGP, PE1 then connected to P Router and P Router connects to PE2 Router. PE2 connects to other external BGP Router. For Discussion, PE1, P and PE2 routers reflect MPLS Cloud wher...

Our VPN throughput is horrible and it appears the Virtual-Access 2 is only getting 56K of bandwidth while the previous route had 832. see virtual-access 2 below.Virtual-Access2 is up, line protocol is up Hardware is Virtual Access interface MTU 1...

I have some 3845 routers with 25MB Dram,time has come to upgrade to 512MBis there antway to determine the existing Dram is 1 x 256MB or 2 X 128MBobviously if it is 1 x 256MB then I only need to get another 256MB to bring it up to 512MB, but if it is...

A card of 8A/S serial ports (A slot is having 8 serial port)can be replaced with a card of 8 (WIC)smart serial port.If it is available than what is the cost of a card and also attach a photo of card if possible.

Hi,We have a LAN of 20 switches - 19 L2 2950 and one L3 3560 switch. Total number of VLAN are 20. L3 swicth acts as the default gateway of all VLAN - subnet. All the servers are attached to L3 swicth. Default STP is running on all switches and one ...

Hello,Thank you in advance for any help. I have a Cisco7021 which works as follows: ppoe-pptp users + NAT+ Statistics collection on NetFlow (ip flow ingress - egress).In general all works, but 50% of the traffic downloaded under natted ip written on...

Hi,We have received 3560 with IOS Version 12.2(35)SE5, RELEASE SOFTWARE (fc1). Is this the final and general deployment IOS? How to check it this is the best IOS for 3560 with most likely no any bugs in IOS.Please share the experience.Any link on cis...

Hello,I have a cisco 877 with 3 vlans and and atm interface with a bvi interface. Vlan 2 and 4 : are nat inside. two different subnetsVlan 3: bridged directly to atm.BVI1: nat outside. gets its ip address via dhcp.I have some static nat port translat...

I have 2 providers for my customers, 1st is 20 meg and they provide the routing and a 2nd 100 meg link which we provide routing. Currently I have a 3550 w/EMI routing to one provider and a vlan for the other. Will a 2821 w/ max memory give me the f...

R1MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255Encapsulation PPP, crc 16, loopback not setKeepalive set (10 sec)LCP Open Open: CDPCP, IPCP Last input 00:00:02, output 00:00:00, output hang never Last cl...

Hallo, I got curious problem on my c1802. I updated IOS from 12.4.15t6 to 15.0.1M and then back to 12.4.24.t2 and meny times I change ADSL firmware too. Noticed that my original ADSL FW 3.0.14 was in new IOS 15 builds useless because established conn...

Hi folks,I have a configuration with 2 physical WAN interfaces (each one 1024 kbps) and one Multilink group as follows:RouterA_|====1024====|_RouterB________|====1024====|interface Multilink7 description ENLACE XXXXXXXXXXX bandwidth 1024 ip address X...

Greetings, we have a client that wishes to deploy 3G GSM services to their remote offices using the HWIC-3G-GSM WIC's for the 1800 ISR's.Ive been onto Cisco.com and found the following link:http://www.cisco.com/en/US/prod/routers/networking_solutions...

We have a Cisco 1811W router for our gateway to the Internet. I just setup McAfee Groupshield on a new Exchange server. When I tried to run updates, they would fail. It uses HTTP over port 80 to download the updates. The updates would start to downlo...

I need some help to set up this router.. I need to understand if SHDSL on router modem can connect to normal asdl 2+ too line o i need SHDSL line only because i'm trying to connect but the interface don't come up