Hi all, We are a Cisco shop but I would like to know if anyone has any thoughts on BitTorrent and there are any implications or issues that might arise if a company would adopt it. Thanks, sK
Hi all, We are a Cisco shop but I would like to know if anyone has any thoughts on BitTorrent and there are any implications or issues that might arise if a company would adopt it. Thanks, sK
Just a check to verify that a 2811 can only handle a maximum of two T1s. Is that correct? Thakns in advance! All replies rated.
Hi All,We are going to host VOIP. We will be getting T1 and cable connection. May I know, which Cisco router will support for Failover setup to perform between these cable and T1 connection. How can I perform the same?Thank you
I posted this in the ME section, but thought I would get some views here.Can someone please help and give suggestions and possible configuration options for setting up metro ethernet in the following senario: Will be setting up ME between headquarter...
I am trying to find the firmware for a WRV210 router. Linksys.com sends me here and on this site I can't find it. My router needs reset daily and I want to find better firmware. Can someone please help?
Hello,Can I use the 1841 FastEthernet0/0 as the connection port to my ISP?I have a T1 WIC, but am switching to an ethernet circuit from my provider.Also - do you have configuration examples?Thanks!
The command lookup tool verbage for default behavior on these commands is very elusive/confusing.This is the way I understand it: 12.0 - 12.1(5) service fingerdefault = ENABLEDip finger12.2 - onwardintegrated-introduced in 12.2default behavior is DI...
What is done to readvertise routes learned bia BGP.For instance, I have 2 separate networks 10.1.1.0 and 10.2.2.0.In the topologyCE Router 10.1.1.0 --- PE RouterA --- Pe RouterB --- CE Router 10.2.2.0If CE Router 10.1.1.0 advertises its routes to PE ...
HelloI have two routers 3825 both having one Internet link and MPLS link from different subscribers as shown in the attachment. Site 1 consists of RTR A and RTR B . And site 2 consists of RTR A and RTR B . Now I want to have MPLS and Internet link bo...
I'm having trouble identifying where and how certain metrics are arrived at on my network and was hoping someone may have some insight. I was unable to get to the bottom of it with TAC.I've got a L3 MAN environment with 3 WAN aggregation routers spr...
Hi,I've got a site with 2 E1's connected in an ATM IMA configuration.The router card is an NM-ATM-4E1. I'm getting constant member state changes in the logs even though the connection is not dropping. The CIR from the telco is 2048Mbps.Does this mean...
Hi,Could anyone say why we use MPLS in multicast mode?It could be protection. But outside protection, are there other reasons?Thanks for your words.Best regards,Michelot
Hello, thanks for the support of this expert forum. I have a replication link issue involving the capabilities of automating failover across L2 circuits. BOX A & B are 6513s running in Dual MPLS private WAN environment in 2 seperate Datacenter locati...
I am getting ready to deploy a DMVPN solution with hub-to-spoke using GRE. Question "is there any QoS support for one remote spoke site to have some kind of traffic shaping, not a hub-to-spoke or spoke-to-spoke type of QoS solution?thanks, Kevin
Does any body are already configure a ISDN BRI Interface as backup line for Serial connection?I have two site that must be connect with ISDN BRI whe the main serial ling goes down.Does any bony have a example ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM | ||
04-24-2024 03:57 AM | ||
04-23-2024 05:38 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |