Hi,I got a second block of ip address, and i need to configure my asa to support second address.I know that in cisco router that is supported and easy to deploy, but in asa i have some trouble to make it working.please can you help me with this
Hi,I got a second block of ip address, and i need to configure my asa to support second address.I know that in cisco router that is supported and easy to deploy, but in asa i have some trouble to make it working.please can you help me with this
Hello,We have a rather odd issue with some backup static routes on my MPLS routers that I've yet to figure out the cause.We use BGP for routing on the MPLS, but in the event that a site has its circuits go down, we have static routes with a distance ...
Hi All,I'm trying to configure a IPSEC VPN between two sites but can't get it to work.-----------------------------------------Network Topolgy-----------------------------------------[LAN1: 192.168.199.0/24] -> [Cisco 2600: ADSL Connection] -> Intern...
HiI am sorry for my question as it is too simpleQ. what command can make me find the port no. of multilayer switch which has as specific IP add (eg. 172.12.x.x)connected to it
We were having issues with our staff access to the internet that prompted the management to direct the Info Tech Department to deny some specific systems access to the internet.To deny internet access to systems, we basically deny address translation...
What is the meaning of this line in PIX--static (inside,outside) 10.48.0.0 10.48.0.0 netmask 255.252.0.0
I try to install a nm-1a-oc3-pom on a 3845 router with c3845-ipbase-mz.124-24.T.bin the port adapter is not recognize ??? wich ios i need the configurator dont know this card
I am trying to configure LFI but my virtual interface is down, does anybody has basic working configs for me. below are my configs:-!interface Virtual-Template1 no ip address ppp multilink ppp multilink interleave ppp multilink fragment delay 20 ip r...
Hi,I realised there is a new BGP command in IOS 12.4:suppress-inactive - Suppress routes that are not in the routing table.I.e., this commands stops advertising BGP prefixes which failed to be written to the RIB (there is another route available wi...
i have a port adapter nm-1a-oc3-pom with a sfp-oc3-mm i need sm sfp. May i use a 1000base-lx sfp instead ?
Hello all,I have a CPU process problem, the total five minutes CPU is showed 30%. But after I sum all processes, 5Mins is only 1.74, 1Min is 2.05, and 5Secs is 3.43. It is lower than 30%. It is very confused me. What process take use the rest CPU 28%...
I have two routers connected point-to-point by two serial links. i want to load balance with OSPF so that i can run PBR and classify a certain type of traffic to use a single serial and another type to use another serial based on destination ip addre...
I want to create an acl to permit traceroute. But I see two different types of the icmp commands for traceroute. Which pair is correct?>> permit icmp any any ttl-exceed> permit icmp any any port-unreachableor permit icmp any any traceroute
i am unable to telnet cisco 1841 rouer through fast ethernet port.Plese help me
we have a 500M Metro-E link terminated on the fiber 1G port on SUP720 itself (C6500). The switch sees the link as 1G instead of 500M.The challenge is how to achieve QoS for VoIP traffic (dscp EF) without feature support of "shaping" on LAN ports. We ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-28-2024 05:09 AM | ||
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM | ||
04-24-2024 03:57 AM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |