Routing

Hi.We have a 3640 router used as access-server.It's connected to an ISDN Pri line, and all works properly.Now we need Pri line for other purposes, and our RAS users are very few.So we have attached router to a BRI connection, and configured this to a...

Hi everybody,I'd like to know what is the maximum number of E1 ports supported on 7204VXR. For example, if I have two PA-MC-8TE1 installed on my 7204, can I configure and use all the 16 E1 ports at the same time?RegardsStefano

I tried to load IOS from TFTP server but tftpdnld command was not found. Because of this, I changed console speed to highest possible (115200) and transfered IOS image with xmodem command. It went OK and I restarted system. The IOS booted but I didn'...

We had an issue with one of our core 7606 routers. Bug ID: CSCsl50569To prevent issue from occuring in 12.2(33)SRB2, diagnostics can be disabled on the SIP-400 with the following command:Router(config)#no diagnostic monitor module I would like to kno...

Hi,Recently I'm implementing a project of inter-AS multicasting. Within each AS, there are two RP configured with the same IP, using the Anycast method to provide redundancy. Between different AS, MSDP will be used to connect the RP in different AS. ...

How can we check latency on any Router interface.Thanx....

HiWe are seeing small but incrementing amounts on ignored input errors on our 2821 routers. The are incrementing on both the WAN and LAN interfaces (both are ethernet interfaces). I would like to understand possible causes. The error rate is extreme...

Hi,I have an x25 call established between two peers through PAD over XOT. Assuming that i would want a packet transfer to be exchanged between both these peers (two end hosts connected to routers). Can i achieve this through regular ftp?Thanks!

Hi,I have 3750 at location A and 3560 at location B, both are inter linked through gi1/0/28 on both swiches. At location A, I have customer connection to same 3750 port 1 and a same customer on location B connected to switch 3560 port 1.This link is ...

The interface g0/1 of 172.16.1.0/24 of Router is connected to switch with two subnets 172.16.1.0/24 & 172.16.2.0/24. We are running eigrp between them. Currently I'd like to have "ip nat outside" to apply on the outside g0/0 interface in the router a...

HelloI dial into FXO interface on 2651 router, After it answers I hear a ring. However I would like to hear a message that I recorded.I used these commands :telephony-service keepalive 200 moh Shay.wavAm I doing something wrong ? Could any1 point me ...

Dear sir,One of my customer is looking for router wichich will support broad band and leased line.He was having 2 broad bands (ADSL) and one leased line (V.35) now he was planing to connect the 2 broad bands and leased line in single router and he wa...

I have 2620XM router with IOS 12.2 with crypto feature set.I want to enable keepalive on tunnel interface for the tunnel interface to go down incase of link failure.The problem I have current IOS version doesn't support the keepalive command on Tunne...

Hi,We are getting the error message when we are trying to save the configuration.% Error saving SNMP ifIndexes No space left on device% Error saving SNMP ifIndexes No space left on device[OK]Directory of flash:/ 1 -rw- 9304844 ...

I'm planning on installing new 6509's with Sup 720's. I don't have any 720's installed as of yet so I can't play around to see if this is supported. My 4506's running IOS ver. 12.2(25) doesn't support GLBP. Do any of the other sup's or IOS versions f...