WHat is EIGRP ID? Is it something like ROuter ID on OSPF? How this parameter can be used? thanks.
WHat is EIGRP ID? Is it something like ROuter ID on OSPF? How this parameter can be used? thanks.
Why EIGRP summarizes only 10.X.X.X and 172.16.X.X ? What about 192.168.X.X isn't it the same type of address?
Hi AllI have the following Wireless Router Cisco Aironet 1240AG and I have a SONY VIO N320-E/W Laptop.It shows me under the available wireless networks and when I try to connect to it it fails and after diagonizing the problem I get the following mes...
Hi - I noticed something that maybe someone can explain to me if this is unusual or normal. Notice that the IOS version is not the same as the BOOTLDR version even though the router has the boot system command.------------------------Cisco IOS Softwa...
I have a site that has a single MPLS link to it,I have an ASA firewall out there connected to a DSL internet connection. My question is where can I find a good guide to help me configure routing my router or switch to use the ASA VPN tunnel back to ...
For a mistake I've forgot a non-existent inbound route-map applied to a BGP neighbor and this router has not been receiving any advertisements from this neighbor.So I need to make sure this issue is caused by the non-existent route-map or it could be...
Hi,We have a site that is connected through fiber to the main office, we would like to create a backup link for a group of user (on a specific switch) to be able to connect to the main office through a T1 line if the fiber was accidentally damaged. W...
I have Router with 3 Ethernet-portsISP1= connected to F0/0ISP2= connected to F0/1 Inside = connected to LAN F1/1Is there a way to make load-balancing and Failover for these Internet Link.The idea behind this is to have Office-executive browse interne...
I have a WS-C6513 running cat6000-up2cvk8.8-4-2.bin and a WS-X6516-GBIC card module...is there a command that I can use in CAT os to shut this line card down before I remove it? or do I just pull it and hope for the best?Greatly appreciate the help!...
Hi Guys,Is there a IOS image that i can use with 3475 router and get SSH 3 support as a feature.ChaoVishwa.
We have a network with a Catalyst 500 switch and a 871 Ethernet router. The router has been configured ,with SDM, a SDM default medium security firewall. We observe that there is continuous traffic between the router and the internet(DSL modem). I ...
Hi,I have question about NAT and routing NAT-ed address over EIGRP. If i NAT source host on Router A, Router B will see this network as it is and i would like it to learn NAT-ed address so it can return packets for it withaout static routes. Is this ...
Hello,I have site-to-site VPN between HQ & branch-officeOSPF is the routing protocol used between VPN Tunnel.Since I have limited bandwidth at branch-office ; I need to restrict ospf update once a dayI need to know ; how to restrict the updates once ...
Dear sir, whether the 4 HWIC serial ports are configured as ppp multilinkUsing 2821 and 2811 routers individually. Plz conformsrini
My 2800 Series Router is unable to boot.Following are the boot sequnce caputure of the Router when it is powered on.Please any one reply me.If any of the above Memory Requirements are "UNKNOWN", you may be us...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 03:04 PM | ||
04-26-2024 01:23 PM | ||
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |