can anyone tell me the basic commands to setup vpn server on 877 router
can anyone tell me the basic commands to setup vpn server on 877 router
Hi,Is it possible to track the number of bgp prefixes and warn when they fall below a threshold?I understand maximum-prefix will warn when the number of prefixes exceed the threshold, however I want to know when the number falls below a set value.Tha...
I'm trying to gain access to vlans at a remote ATM-connected site and assign them to ports on a switch at a central location. I need to do this for about 10 remote sites, one at a time. I was told that L2TPv3 was a good thing to use for this. Now, wi...
I have 6 T1s that are to be multilinked on a 8-T1 card on a 7206. When I have the Multilink on, all of the serial interfaces go to up/down. When I shut the multilink down, the interfaces go to up/up. Ive confirmed timing, linecode, framing. Here ...
Hello all!I have a "stupid" situation.OSPF process between 2 interfaces with different MTU values and of course the EXSTART/EXCHANGE stuck situation.I put "ip ospf mtu-ignore" and I worked fine until yesterday, when one of the interfaces went down.Af...
Hi all,I have a 2801 router. I have a 34MB link from ISP plugged at my interface f0/1, but I would like to use only 12MB. Can I restrict the bandwitch on the router?ThanksTauer
Hi,I would like to configure site-to-site vpn failover between 2 1811 router.Does anybody have any idea how to do it?The ios is 12.4(6)T9.Thanks,
Hi,I have two links from site A to Site B one link 2 MB is directly connected and other one is of 4 MB thru the service provider. I'm using EIGRP b/w Sites. Using EBGP b/w router A-SP & SP-B for the service provider network. On router C I'm seeing th...
I'm setting up a new ISDN link. The link thous the NT Box shows the line as active does not come up. I have checked with local telco and they've confirmed the line as being OK. The show isdn status output is as follow:003R#show isdn statusISDN BRI3/1...
getting error" Bad RAM at location 0xA0000424: wrote 0xA0000424, read 0xA0000464" in 3660 router.Router went down thrice ,after rebooting comes up.Please suggest.
pls i have a link that is 128 kbs , i know how to get the amount of load passing thru, what i dont kow is how to measure the current bandwith
I am working with a 3845 with 3 dual T1 WICS and 2 2851's with 1 dual T1 and a single T1 WIC. Having trouble getting them to communicate across simulated T1 connections. I have made the test cables for loopbacks and have all WICS connected (3 to ea...
Just have a quick question here:*Jun 25 18:41:25.628 UTC: IP: s=200.13.119.40 (GigabitEthernet0/1), d=205.248.197.130 (FastEthernet1/0), len 284, access denied*Jun 25 18:41:25.628 UTC: ICMP type=0, code=0Am I reading this correctly when I do a pi...
Hello,I'm receiving this error while logging my ACL's. %SEC-6-IPACCESSLOGRL: access-list logging rate-limited or missed XX packets.I know that this means the logging is not reporting some packets, but how would you resolve this issue? I'm logging to ...
All,What is the recomended OSPF hello interval for use in production across a P2P link. 10 is default(40 is dead time). Will there be any recomended production usable reconfigurations ( lesser hellos like 5) across a P2P link..?Thank youMS
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-27-2024 07:51 PM | ||
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM | ||
04-24-2024 03:57 AM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |