Hi, does anyone know what the tunnel interface number is with the following command? Like, would it represent a predefined vlan or something like that? ========6513(config-subif)#ip unnumbered tunnel ? <0-2147483647> Tunnel interface number
Hi,I need to update the MSFC on my 6509. Can you tell me the recommended steps for doing so. Pleae see output of my MSFC.od Slot Ports Module-Type Model Sub Status-- ---- ----- ------------------------- -----------------...
hi, i want to know if authentication proxy feature that is available on cisco IOS firewall is use only for HTTP,HTTPS,TELNET and SSH. if an external user need to access to a service that no support authentication such as multimedia application, can i...
I have recently began having trouble uploading files larger than 5mb. I looked in my router logs and saw the following error message - " %IP_VFR-4-FRAG_TABLE_OVERFLOW: Vlan1: the fragment table has reached its maximum threshold 16"Could this be causi...
OK, another silly question for folks as experienced as yourselves, but here goes anyway.We are bringing up T3s in our data centers (CA and GA) in prep for an MPLS migration from PRVPN. This is the first time I have dealt with a NM1-T3/E3 module. Both...
Hello,I am trying to set up bonded T1 to failover to DSL. Below is my set up.An ASA 5505 is connected to inside network and also conencts to f0/0 on a 2811. 2811 has dual T1 cord with two T1 bonded using MLPPP. Multilink interface is my promary ro...
Greetings,I posted a question previously about how to configure NTP to keep it from accepting queries or broadcasting. Now I'm running into problems with synchronization.As mentioned previously, I'm trying to sync an internal router with an external ...
Hi Pros,I m getting the below error message in a router:*May 20 09:50:04.503: %LINK-3-UPDOWN: Interface BRI3/0:1, changed state to up*May 20 09:50:04.503: BR3/0:1 PPP: Using dialer call direction*May 20 09:50:04.503: BR3/0:1 PPP: Treating connection ...
Hi all,I have a question regarding our BGP configuration that's getting me mad. We have two 7604 doing eBGP with three providers and iBGP between them.This is our config for the iBGP peeering (some data changed to protect the innocent)router1:router ...
show interface does not show my E3/T3 wic but show ver does :Cisco 3825 (revision 1.2) with 226304K/35840K bytes of memory.Processor board ID FTX1136A37U2 Gigabit Ethernet interfaces1 Subrate T3/E3 portDRAM configuration is 64 bits wide with parity e...
Hi,I have a range of ip address, and have all my LANs nat'ed to a single IP address.All this works fine.Now I want to add a static entry, to port forward SMTP arriving on my public IP address to an internal server.(The outgoing traffic from the inter...
I'm trying to remove a private AS from being announced to a peer but I'm unable to. I'm using hte REMOVE-PRIVATE-AS but it doesn't seem to have any effect.Here's my setup:1605R <----> 1841 <----> 2651XMAS65000 AS19262 AS65000There are no c...
does this statement indicate thatthe switch will acquire a dhcp addressfrom the router?!interface Vlan1 no ip address no ip route-cache shutdown!interface Vlan134 ip address dhcp no ip route-cache!ip http serverIm adding a switch to the network andna...
Hi, I have two BGP routers configured to peer with two different ISP. All works well.I am using HSRP on the LAN to track the primary link and if that fails, use the secondary link.The problem is that I experienced an issue where the physical link did...
