Hi all,i am trying to set up a source device for IPM. But the source selctor does not show any device. In the LMS portal for IPM indicates under IPM Device Categorization no IPSLA enabled devices. Thank you in advanced.
Hi all,i am trying to set up a source device for IPM. But the source selctor does not show any device. In the LMS portal for IPM indicates under IPM Device Categorization no IPSLA enabled devices. Thank you in advanced.
Hi,allThanks in advanceTheir is some confusion in qos configuration in mpls network.One of my customer wants to deploy qos for bandwidth management in mpls network.Scenario is like below.MPLS sp provides 18 mb ethernet connection to customer.Bandwidt...
Which queing and compression techniques are needed to effectively use the available bandwidth for voice traffic? (Choose the best Two)A. CBWFQB. LLQC. PQ or CQD. RTP header compressionE. TCP header compression
Hi,I cannot ssh to my router (878) from outside. I have an access-list on the outside vlan and I can see that it is being hit on the ssh entry, but it just times out. I can ssh from inside no problem. Any ideas what could be wrong. I have PAT/interf...
Hi All,I have just upgraded my WS-2960G-48TC Switches, enabled SSH but I can access the Switch using both protocols - how can I disable Telnet and permit SSH
Hello everybody,does anybody knows if it's possible to plug a NM-1E module which is currently running on a Cisco 2621 in a Cisco 2851 ?Thank you very much for your feedback!Kind regardsStephan
i have 2 leased line and one R/F connected to my 1841 router, I want to know the best possble way make failover connection, IF one link is down other should start automatically.
Has anyone ever seen this? In the output of a "show interface g0/0" on my 3825 router I am seeing a lot of "unknown protocol drops". Oddly enough it is the same number of broadcasts. This is causing an off-site location to record 13 percent loss.
Hi AllI have three sites (A,B,C) connected through MPLS-VPN using protocol BGP with AD 20(EBGP).Site A is our central site and we have secondary link (VSAT),Site A to B and A to C. Now I want to use same protocol for secondary link and traffic should...
Hi AllI wonder if someone can help me with a NAT problem. It's seems to be a relatively simple setup, but I cant get it to work properly.Ive set up a simple lab as follows:laptop1<-->fe0/1-router-fe0/0<-->laptop2laptop1-eth1 = 1.1.1.100laptop1-eth1:...
First off , when I use the word "work or worked" Im reffering to being able to get out on the internet.Recently I was able to make an Embarq DSL modem work with a cisco router behind it. The modem however was NOT in bridge mode.Now I want to make th...
This is the situation. We have two Carriers' MPLS clouds at two locations for redundancy. Each Carrier provides us a managed (CE) router to connect to their MPLS cloud. We connect two of our routers to the two Carriers' CE routers at each location...
I put my embarq Modem in bridge mode. Setup my cisco 2621 behind the Modem. Setup DHCP on the WAN fa0/0 and its pulling a public IP address. I then set my LAN fa0/1 to assign DHCP pool along with embarq DNS to clients on my home LAN. I get IPs on...
My current network I have two connections with two CSU/DSU connected to external encryption devices connected to a serial interface port on a 3825 series cisco router. The distant end is connected the same way. My first connection I have pulse-time 5...
This is my scenario and I want to do end-to-end VoIP QoS. My L2 is a Cisco 3750, L3 being Cisco 6500 and the routers are Cisco 3825desktop --> phone --->L2 ----> trunk ------> core ----> router ---> router ---> core ---> trunk ---> L2 --> phone --> ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 03:04 PM | ||
04-26-2024 01:23 PM | ||
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |