%ALIGN-3-TRACE: -Traceback= 402B4DA4 40ACAB98 40AC9238 401E9B44 401E9B30 00000000 00000000 00000000Can someone assist with this?
%ALIGN-3-TRACE: -Traceback= 402B4DA4 40ACAB98 40AC9238 401E9B44 401E9B30 00000000 00000000 00000000Can someone assist with this?
Hi,I am setting up a new network. Is NAT configured on the perimeter router, or the ASA5505 firewall?Thanks.
I have an GRE/IPSEC VPN tunnel backing up a T1 link. Telco problem brought the T1 down. Tunnel works/passes data but Window's name resolution was only working from "some" servers and pcs on either side of the tunnel. First, I was under the impressi...
Hi,I am little confused between two commands..plz explain the usuage ..address-family mdt or address-family ipv multicastRgds,Gaurav
On a cisco 6509 sup720, that has peerroutes and transit routes, is their a way to limit a customer to only the peerroutes. I've seen issues with a customer still sending me traffic that's not destined for any network in his bgp peer routes that I sen...
I have an X.25 over ISDN configuration which running on a 1721 router. I can telnet from a host to port 1998/tcp (XOT) on the router. This configuration is to be migrated to an 876 router, but I am unable to connect to the XOT port with the same conf...
I am wanting to connect multiple internet connections (T3,Cable Modem,DSL) each direcly connected to the switch and do load balancing between them. Of course each interface on the switch will have IP blocks setup and I need to NAT them.Before I buy a...
i have an existing connection to a single ISP (ASA_1 -> 2811_1 -> ISP1).We are adding a second ISP (ISP2) for redundancy and load sharing between the two WAN links. We want to maintain conncetivity if one ISP link is down.On my side, I am adding a se...
router 2611 IOS is gone.I tried to copy the IOS through xmodem.the IOS size is around 12.5 MB.When it starts copying the IOS it says the time remaining is around 6 hrs..i tried it yesterday and when it was around 45% it stopped and restarted again..F...
I am trying to figure out what IOS is needed on my 2620 to be able to run the command "crypto key generate ...".Thank you
we have GRE tunnel between data center and remote site on AT & T link in which IP MTU 1476 is configured in tunnel interface at remote site while and no Ip tcp adjust-mss command. And on data center end tunnel is configured with Ip tcp adjust-mss 143...
Here is my topology and my problemRouter (R1)Serial 1/1 connected to s1/1 of R2 12.0.0.1/30Loopback 0 100.0.0.1/24Router (R2)Serial1/1 connected to s1/1 of R1 12.0.0.2/30Serial1/3 connected to s1/3 of R3 23.0.0.1/30Serial1/2 connected to s1/1 of...
Hi All,I have a query as follows:X NET (100.200.1.X) ------[(NAT outside int)-NAT Router-(NAT inside int)] ------- Y NET (192.168.1.X)Suppose I have configured NAT to translate 192.168.1.x network to 100.200.1.X.If I ping/trace from X NET on NATted I...
I have a 871w connected to a cable-provider in Vienna, Austria.The speed should be 16384 mbit download, 1024mbit upload. But I only get something like 3 mbit down, sometimes peaks of 5 mbit.I run the test with an ISP-provided testsite (1MB file per P...
I am using an 871 to connect to an ISP that requires my outside inteface to be in DHCP mode. I give the ISP the MAC address of this interface and my "static" IP is assigned via DHCP based on this MAC. Now I need a second IP and the ISP is asking fo...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 03:04 PM | ||
04-26-2024 01:23 PM | ||
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |