hi , i ve a cisco router 2801 , with 2 fa ethernet ports. can i install 1 more module with 2 fastethernet ports?
hi , i ve a cisco router 2801 , with 2 fa ethernet ports. can i install 1 more module with 2 fastethernet ports?
Dear All,Please share the possible way of swapping Destination and Source MAC to test the loopback on Ethernet MEN circuits.
Hi,I have a 4 lease line.Can any body tell mMbps (1:2) Internet e what is the maximum bandwidth i can get .IS that 2 Mbps ???
I have a primary site with private connection via MPLS and then I have a cable modem connection. Right now we use 2801 router for primary connection and pix 501 for backup connection via VPN. The fail over is not automatic. Anything I can do?
Hi Experts,Once done with the ipsec configuration, I would like to test and verify the traffic by using debug/show commands..Any debug/show commands that can help me to differentiate non-encrypted and encrypted traffics?OR how can I observed which on...
Hi,I have four 4700 routers and all of them are 2FE + T1 config. Does 4700 support 3 FE? I remove the WAN card and install 3rd FE card ?regards
Hi,Suddenly our Network got hanged which is cisco 3745 series.After restarting the router it went UP.what could be the problem ?what are the commands i can use to know the reason?regdsNasheer
Hello everybody,i have read some documents about cisco Load balance features (SLB) and it looks good, but unfortunately i can't use it on my 2811 router. So i have to do something to balance my outside to inside traffic. Here is what i mean. Let's sa...
Hi all. Very new with QOS. I have 5 remote sites. 3 sites connect to an mpls cloud using 2821 router/25mbps pipe. 2 sites have 3750me switches. Bandwidth to these sites is 100/250mbps. I am looking to shape the traffic leaving these sites, so an...
can 2950 switch still be used on current CCNA, CCNP practice? what about later on in CCIE?
There's two WAN nodes on cisco 28xx and 871 with 2 satelite hops between them. Link throughput is 64Kb/sec. Encryption with IPSec tunnel applied between routers. TCP sessions in such a scheme are very slow and applications goes timed out. All my trie...
I'm configuring C3660 for PPPoE subscribers. I'm just trying to use feature ârange [range-name] pvc start-vpi/start-vci end-vpi/end-vciâ under ATM interface configurations. Router(config)#interface atM 1/0.4 multipoint Router(config-subif)# Here...
Hello friends,Can anybody tell me how to solve issue if traffice from certain devices are coming/going with an ip address instead of hostnmae?I checked config & seems all right, but DNSIX is not enabled on those devices. does it make any sense???Ple...
We have a network admin who bought two of these 877 routers (MFG# CISCO877W-G-A-K9) after opening both the boxes he realised he wanted to get a router with 10/100 ethernet port on the WAN side. Since Cisco has this policy of no RMA for opened boxes I...
How much presentage of the bandwidth does EIGRP uses for it self. And what exactly does that mean. For instance this bandwidth is reserved only for EIGRP's message and cannot be use for data or something else. And also if we use redistibution with sp...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM | ||
04-24-2024 03:57 AM | ||
04-23-2024 05:38 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |