Hi, I can connect to my ISP (Telia, Sweden), but I don't get a ip from my ISP. I think that the router cant't receive any DNS... Telia use dynamic DHCP and DNS. I have set the encapsulation mode to "RFC 1483 llc/snap"
Hi, I can connect to my ISP (Telia, Sweden), but I don't get a ip from my ISP. I think that the router cant't receive any DNS... Telia use dynamic DHCP and DNS. I have set the encapsulation mode to "RFC 1483 llc/snap"
Hi,My router A is connected to 2 upstream routers,as below,1-Router A---fa0/0---R12-Router A---Fa0/1---R2All 3 routers running OSPF , I would like Router A to prefer 1st link over 2nd link.does puting the lower cost on 1st link interface will do the ...
I have a cisco 2811 without DSPs and I have installed 4 VWIC-2MFT-E1. At the moment I want to configure the E1s I can't because the VWICs are not recognized by the router, it displays a message that it requires DSPs, but actually I want to configure ...
Imagine between my data center and a security guard facility 500 yards away, I need to provide an ethernet drop.The undergroud/conduit intermediate vaults are dirty, susceptible to humidity. I have no power available there (other than the PoE provide...
Hi,This is one of the interesting issue which i am facing. Whenever my client tries to send a file less than 1kb, the file is transmitted successfully over ftp, but for files greater than 1kb, the files are not being transferred, instead a 0 kb file ...
Hai frenz, may be an easy question to you all but i have doubt ...pls do help me1.why do we need AS Number, 2.in what situation AS number is needed?? 3.if my customer using AS do i also need to have AS to talk to his router4.if i dont have AS .. can ...
Hi all,I believe that rmon is configured on our CatOs switches.In order to see/use the RMON data from our FLUKE device which is a different monitoring device, we need to know the RMON READ and the RMON READ/Write community string.Can you please let m...
Can anybody explain me the exact difference between the below mentioned commands and which when should be used where in configuration.1) rate-limit input 64000 8000 8000 conform-action transmit exceed-action drop2)traffic-shape rate 64000 8000 8000 1...
I am attempting to redistribute a default route into my eigrp process via a route map and acl, but the route is not being injected into EIGRP. I'm using the following commands, and I see the static in the routing table, as well as matching against th...
Hello, I am just wondering if someone can shed some light. When i do " sh ip bgp neigh x.x.x.x receive-route i see couple of networks marked as "h". According to the defination it means "h-The table entry history".. What does this table entry histor...
Hello,We currently have some old and hard to use Vina routers installed that allow us to send/receive calls and data between our remote site and our main site. The routers either have fxo or fxs cards in them depending on which site they are in. At ...
We have purchased a router cisco 2821. I want to configure a E1 unchannelized (not PRI)interface for 2 MB of bandwidth. Please guide me from where i can get help URL to configure my E1 interface for 2 MB of bandwidth.
I have a Cisco 837 for home Internet. I also use it to VPN to work, I use the Cisco VPN Client, I don't want a dedicated VPN, but what is this Easy VPN client feature? Can my router connect to work like the VPN Client, but the router does it?
I am setting up a VWIC2-1MFT-T1/E1 for a data T1 and I have found lots of information on how to set the card up for voice but I understand it can just be a normal Data T1 as well. Is there some good documentation on setting this card up for just dat...
I had planned on putting: clock source line independent on each controller but "independent" isn't recognized. I am planning on using multilink with 6 T1s between two identical 2811 with one side as internal and the other as line. I understand that...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM | ||
04-24-2024 03:57 AM | ||
04-23-2024 05:38 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |