how can i arreange proirity bandwith for ftp uses over wan?
how can i arreange proirity bandwith for ftp uses over wan?
Hi,We would like to config following:1. setup tunnel in between R1 and R22. R1 is "ip nat inside" and R2 is "ip nat oustde" 3. I would like all users to access "66.x.x.2" this server, it must go to tunnel and through R2, R3 to outside internet to 66....
Hi all, I'm going through a FR lab and I am seeing some unexpected behavior. Namely, I have a FR hub router with 3 FR spokes, and when I ping from one spoke to another with "debug frame packet" on the hub router I see what appears to be packets smac...
We have implemented WCCP between Cisco router and Bluecoat cache engine, there's a ASA placed in between so we have configured the firewall to allow ports (UDP 2048, & GRE) in order for the WCCP sessions to be established. The WCCP sessions is being ...
occasionally I have to troubleshoot faults on cisco routers and need to create loopbacks for T3 circuits. Can anyone tell me where I can buy connector for these T3 cables?Thanks
Hi any body can tell , Can it possible to create NAT GRE tunnel , i mean to say suppose i have two router and connected with tunnel, I want to hide my source ip address .Please help me or give me some documents which help to understand.-v
In Cisco IOS documentation, some IOS commands are described as running in 'EXEC mode', while others list USER EXEC mode or PRIV EXEC mode or both. When only ?EXEC mode? is specified, does this mean both USER EXEC and PRIV EXEC modes ? Or is it referi...
Hi,Need help on the following:The following only happened recently and no configuration change was done. The impact is that the session and application layer can't connect from end to end server.the following are the error messages that are logged on...
I have included a config and the "sho ip route" output of a router that is behaving strangely. As you can see, I have static routes to 65.171.249.0 that don't show in the routing table. I know that sometimes "floating static" routes are hidden by r...
I have a requirement to emulate our customer's network in our lab. The customer has three separate WAN coming in and they are used to communicate with the internal servers with different purposes. Now I only have a single WAN handoff from our ISP wit...
Hi,Users connected to my switch complaints slowness or timeout to application server.Our Application Server looks ok, users on other switch doesnt complaint..What is the best tool or command-line commands to identify the problem of high utilization o...
Hello everyone, im looking the reason about a router 1721 its re-starting many times (reach until it has to decompress the image) when it has a IOS c1700-k9o3sy7-mz.123-2.XE.bin. Someone knows why?
Hi Sir,My customer requires T3 connectivity for their Cisco 3825 ISR.Is NM-1T3/E3 the only option? Its data sheet as follows:http://www.cisco.com/en/US/products/hw/modules/ps2797/products_data_sheet09186a008010fba2.htmlKindly advise if there's any is...
Hi,I'm trying to add on to an existing VPN between a cisco ASA5510 and a PIX 501. Currently, the vpn is working and traffic from vlan 10 on the asa box can communicate with traffic on the pix box, and vice versa. However, I also need the traffic on...
Hello, I have 3 conections to my ISP. All of them are frame relay (E1), my problem is:I configure as follow:interface FastEthernet0/0ip address 10.10.10.1ip route 0.0.0.0 0.0.0.0 10.10.10.200 (ISP IP ADDRESS)when I configure this like that everything...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 03:04 PM | ||
04-26-2024 01:23 PM | ||
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |