Hi All Manish this side,I just want to know that can we achive load sharing and redundancy both, while using HSRP.
Hi All Manish this side,I just want to know that can we achive load sharing and redundancy both, while using HSRP.
hii have seen the unnumbered interface being used in a number of occassions but i cant really understand why,i mean if one can just configure an ip address why not just use an ip address,why do we really have to configure an ip unnumbered interface.
Hi, I configured the following lines for a cisco 3825 which needs an E1 interface to connect to a PBX and a E1 interfaces to connect to a E1 G.703 Wan link, however I am not sure wheter or not I need to add all these parts such as NM-HDV and DSP or a...
hi..i have been using aaa authentication login default local and enter username user1 privilege level 15 password user1. i hope by login with that username that user will raise the level automatically when ssh /telnet. is the way i do is wrong? tx
People, When I try apply the access list I received this message:Did you Somebody already receive somethink same this?
Hi,I need to setup 2 VLANs on the 877 Router and there is a need to ACL the 2 VLANs I create on the router.How would I go about doing that?
Hi all,i'm setting up an inbound ACL on the gateway's WAN interface. i want to allow all GRE & PPTP traffic from my Win2k VPN peers to my Win2k VPN server, and deny other IP traffic to this server. i did the following: 10 permit tcp host remote_pe...
Internet Router/Firewall/VPN with 4xT1--------Internal LANWill this work?the MLPPP will be the outside but what will the Firewall use as it's outside address.We also have a class C network. How can I use the class C network on the outside firewall a...
Hi,What could be the reason for the following Symptom.Interface Status:- Down.Interface Line protocol:- UPHas anyone experienced such type of problem? If yes please share.Thanks:Ajeet
Hi to all,I have some questions about LLQ on ATM PVCs.The config output is from the CPE (Cisco 878):controller DSL 0 mode atm line-term cpe line-mode 2-wire line-zero dsl-mode shdsl symmetric annex B line-rate autointerface ATM0 bandwidth 1536 no ip ...
HiI have two routers connected through Public carrier provided MPLS netwro.Both can ping on thier serial interfaces alongwith service provider end IPS. but failed to ping on each other local fast ethernet. The configuration of Router 'A' is here:inte...
Hi AllI need to Terminate fibre using a router,2800 ISR and was wondering if someone knows which modules does this.Thanks in AdvanceTau
Router 1841 doesn;t show temperature status when I run command sh env whereas 2800 is showing.The IOS is 12.4 on bothKindly suggest??Output:sh envFAN 1 Running sucessfullyILP Power Supply - Absent
Hi,Cisco 877W ADSL Router causing errors below. This happens each time I do a 'show run'Is there a fix for this?*Mar 6 06:02:56.613: %SYS-3-CPUHOG: Task is running for (5000)msecs, more than(5000)msecs (10/6),process = Exec.-Traceback= 0x80132C74 0x...
Hi Sir,Can we configure E1 links with no G.704 framing using the VWIC2-2MFT-T1/E1 (desc: 2-Port 2nd Gen Multiflex Trunk Voice/WAN Int. Card - T1/E1), as follows:!card type e1 0 0!controller E1 0/0/0 channel-group 0 unframed!interface Serial0/0/0:0 .....
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM | ||
04-24-2024 03:57 AM | ||
04-23-2024 05:38 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |