Hello,I need a little help in using the following as-path string._7(5|45(45)?)_ I can't for the life of me remeber how to enter the question mark as a character and not a command. I can't seem to find it on CCO but I know there is a way to use it...
Hello,I need a little help in using the following as-path string._7(5|45(45)?)_ I can't for the life of me remeber how to enter the question mark as a character and not a command. I can't seem to find it on CCO but I know there is a way to use it...
Hi,My 7120 router stuck in romon mode.When i give resetIt gives the following error*** TLB (Load/Fetch) Exception ***Access address = 0x0PC = 0x0, Cause = 0x8, Status Reg = 0x3040d003ROM Monitor Can Not Recover From ExceptionA Board Reset Is Issued**...
hi all,how do i make my pix understand the traffic coming from my remote location office connected through mpls connection we have 1 remote location connected to main office, both sides have routers configured and working properly using ip addresses ...
what exactly is reverse telnet, its use? example pls. thanks
Hi,I hv few bgp queries..1. In my scenario I have iBGP running on many router...do I have to worry about disabling synchronization? Everywhere I read about turning off synchronization I get the examples of transit AS's only.2. External OSPF routes ar...
HelloI have a question about connecting the router to the E1 line, I have no knowledge/experience apart from CCNA. I will connect a 1841 router with WIC-1T module to the E1 line using the X.21 DTE male cable.What additional infomation will I need to...
i have a genral question abt wild card mask.....like if we wanna allow or deny a whole class we write 210.54.8.0 0.0.0.255 but some time we use 210.54.8.0 0.0.0.0........like both thing r same so in which scenario we will use all o's and in which sce...
I need a sample configuration for connecting a 871 to a cable modem. I am using DHCP on the WAN port but can not get internet connectivity from the LAN ports.
Hello I have configured the bandwidth percent remaining command on my network i was wondering if there is a way to test it. Or if anyone spots if i made a mistake. below is the config IP's changed!class-map match-all 25vlan match access-group 106clas...
ip route dest ip dest mask next hop(gateway)The next hop should always be from reference to the source on which this route is configured or it can be the next hop with reference to the dest i.e., next hop from dest.
Hi,We are configuring Dialer watch using BRI ISDN as a back up to serial line. This ISDN interface ( Dialer 0 ) on both the routers is also OSPF enabled.On Cisco's website there is a confgurtaion example of configuring Dialer Watch in which there is...
My carrier has their own CSU/DSU. Is there a way to disable the internal CSU/DSU on a VWIC-2MFT-T1 so that I can use the ports to connect to the external CSU/DSU?
is it each WAN ip connect to internet must be unique???any circumstances can WAN ip from 2 locations be same?
Hi community,Does the ip multicast boundary command work in both directions i.e in and out?Thanks,Mats
can some one tell me the difference of these 2 commands?area 10 nssa default-information-originatearea 10 nssa no-summarysince what I know is they all generate default route into area 10....
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-24-2024 03:30 PM | ||
04-24-2024 03:57 AM | ||
04-23-2024 05:38 PM |
User | Count |
---|---|
11 | |
9 | |
5 | |
2 | |
2 |