Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

2106 WLC Software Upgrade

Hi Guys,

I bought a brand new 2106 WLC and a 1142AP. After going through the standard setup, the 1142 LAP was blinking red, yellow and green. I checked the logs and found the following message;

*Apr 18 10:20:29.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.219.1.26 peer_port: 5246

*Apr 18 10:20:29.000: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Apr 18 10:20:30.392: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.219.1.26 peer_port: 5246

*Apr 18 10:20:30.394: %CAPWAP-5-SENDJOIN: sending Join Request to 10.219.1.26

*Apr 18 10:20:30.394: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Apr 18 10:20:30.405: %CAPWAP-3-ERRORLOG: This AP is not supported in controller version 6.0.196.0

*Apr 18 10:20:30.489: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Apr 18 10:20:30.490: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.219.1.26:5246

I requested the latest IOS and Boot image for the controller from the supplier but he has provided only

AIR-WLC2100-K9-7-0-220-0.aes, no equivalent boot image and has insisted that it is enough to upgrade the controller.

My question is this: Is the AIR-WLC2100-K9-7-0-220-0.aes compatible with the 1142 LAP? And would I be able to upgrade the controller with only the

AIR-WLC2100-K9-7-0-220-0.aes IOS and no equivalent boot image?

Thanks for your promt response.

Regards,

FON

5 REPLIES
Hall of Fame Super Gold

2106 WLC Software Upgrade

April 18???  Is your time and date of the WLC set incorrectly?

Can you please post the output to the following command:

1.  WLC:  sh sysinfo

2.  WAP:  sh version

3.  WAP:  sh inventory

New Member

2106 WLC Software Upgrade

The time and date are correct. April 18 was the day I got the logs.

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 6.0.196.0

RTOS Version..................................... 6.0.196.0

Bootloader Version............................... 4.0.191.0

Emergency Image Version.......................... N/A

Build Type....................................... DATA + WPS

System Name...................................... WLAN

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.828

IP Address....................................... 10.219.1.25

System Up Time................................... 2 days 21 hrs 45 mins 1 secs

System Timezone Location.........................

Configured Country............................... Multiple Countries:US,BE

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +49 C

--More-- or (q)uit

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Enabled

Number of WLANs.................................. 1

3rd Party Access Point Support................... Disabled

Number of Active Clients......................... 0

Burned-in MAC Address............................ 40:55:39:8D:D4:62

APc471.fe8f.f3dc>sh version

Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2010 by Cisco Systems, Inc.

Compiled Tue 01-Jun-10 12:53 by prod_rel_team

ROM: Bootstrap program is C1040 boot loader

BOOTLDR: C1040 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA, RELEASE SOFTWARE (fc3)

APc471.fe8f.f3dc uptime is 0 minutes

System returned to ROM by power-on

System image file is "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-LAP1042N-E-K9    (PowerPC405ex) processor with 98294K/32768K bytes of memory.

Processor board ID FGL1527S1LS

PowerPC405ex CPU at 333Mhz, revision number 0x147E

Last reset from power-on

LWAPP image version 7.0.94.21

1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: C4:71:FE:8F:F3:DC

Part Number                          : 73-12836-04

PCA Assembly Number                  : 800-33767-04

PCA Revision Number                  : A0

PCB Serial Number                    : FOC14425AJ2

Top Assembly Part Number             : 800-33775-01

Top Assembly Serial Number           : FGL1527S1LS

Top Revision Number                  : A0

Product/Model Number                 : AIR-LAP1042N-E-K9

Configuration register is 0xF

APc471.fe8f.f3dc>sh inventory

APc471.fe8f.f3dc>

Hall of Fame Super Silver

Re: 2106 WLC Software Upgrade

The 2106 can go up to 7.0.230.0 code and it does work with the 1142. How are you connecting the AP... Switch or one of the ports from the 2106?

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
New Member

2106 WLC Software Upgrade

I tried connecting the LAP to one of the POE ports on the WLC but is wasn't receiving any DHCP IP so both LAP and WLC are connected to a 2950 PoE switch on VLAN 1. I just installed a 1140 LAP and it is working perfectly with WLC.

can I upgrade the OS of the WLC from 6.0.196.0 to 7.0.220.0 without upgrading the boot s as software ell?

would controller version 7.0.220.0 support the 1142 ?

Hall of Fame Super Gold

Re: 2106 WLC Software Upgrade

You need to run at least 7.0.98.0 to run 1040 WAP.

Sent from Cisco Technical Support iPad App

1229
Views
0
Helpful
5
Replies