Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

AP3602E not join with remote 5508

Hi Team

We have a wlc 5508 in central site. versión 7.6.100

A remote AP 3602E located in remote site. version 12.4.(25e) JAL1a

The AP can´t join and register to WLC.

We can check the AP is seen in WLC in the following Window screen in Monitor > statistics > ap joint and is marked like not joined.

Please check the errormsg.txt file attached : check the request for join and discard from the controller.

I attached several aditional files sh sysinfo and sh version from wlc an WAP

What can we do?

any help is necessary

Regards.

31 REPLIES
Hall of Fame Super Silver

Re: AP3602E not join with remote 5508

Do you have access to the AP?  If so, console into the ap and issue:

capwap ap controller ip address

If not, create an ip helper on the subnet the AP is on

ip helper-address

Then globally on the router

ip forward-protocol udp 12222

ip forward-protocol udp 12223

ip forward-protocol udp 5246

ip forward-protocol udp 5247

Output from the console of the AP would really help and make sure the time on the WLC is correct.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
New Member

AP3602E not join with remote 5508

Hi Scott,

This is the output from the console of the AP

*Jan 24 14:34:42.803: %CAPWAP-3-EVENTLOG: spamResolveStaticGateway - Removing default route for existing gateway 0.0.0.0

*Jan 24 14:34:42.803: %CAPWAP-3-EVENTLOG: spamResolveStaticGateway - Adding default route for gateway 10.180.41.1

*Jan 24 14:34:42.803: %CAPWAP-3-EVENTLOG: spamResolveStaticGateway  - gateway found 10.180.41.1

*Jan 24 14:34:42.803: %CAPWAP-3-EVENTLOG: spamResolveStaticGateway - Removing default route for existing gateway 0.0.0.0

*Jan 24 14:34:42.803: %CAPWAP-3-EVENTLOG: spamResolveStaticGateway - Adding default route for gateway 10.180.41.1

*Jan 24 14:34:42.803: %CAPWAP-3-EVENTLOG: spamResolveStaticGateway  - gateway found 10.180.41.1

*Jan 24 14:34:52.803: %CAPWAP-3-EVENTLOG: Could not discover any MWAR.

*Jan 24 14:34:52.803: %CAPWAP-3-EVENTLOG: Starting Discovery. Initializing discovery latency in discovery responses.

*Jan 24 14:34:52.803: %CAPWAP-3-EVENTLOG: CAPWAP State: Discovery.

My name is Alberto and I am sertorivs coworker.

Best regards.

Hall of Fame Super Silver

Re: AP3602E not join with remote 5508

Can you post the output from when you reboot the AP and let it run for a while. What you have doesn't say much.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
New Member

AP3602E not join with remote 5508

Hi Scott,

The time is correct and is synchronized with an NTP server.

I have also added the commands and status but is not joined

Thanks

Hall of Fame Super Silver

Re: AP3602E not join with remote 5508

Post the full output.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
New Member

Re: AP3602E not join with remote 5508

Hi Scott,

This is the output when reboot the AP.

Thanks.

Hall of Fame Super Silver

AP3602E not join with remote 5508

Clear the ap!

debug capwap console cli

erase /all nvram:

[confirm]

undebug all

reload

[confirm]

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
New Member

Re: AP3602E not join with remote 5508

Hi Scott,

The result is the same, the status is not joined and the output is the same. This is the output of the WLC

*spamApTask0: Jan 29 23:13:40.252: c0:67:af:28:d2:64 Received LWAPP DISCOVERY REQUEST to e4:c7:22:ab:28:80 on port '2'

*spamApTask0: Jan 29 23:13:40.252: c0:67:af:28:d2:64 Discarding discovery request in LWAPP from AP supporting CAPWAP

Thanks.

Hall of Fame Super Silver

Re: AP3602E not join with remote 5508

You have v7.2 on the WLC?

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
New Member

Re: AP3602E not join with remote 5508

The version of wlc is 7.4.110.0

Hall of Fame Super Silver

AP3602E not join with remote 5508

Capture the output again and also run the command I just posted previously and reload without saving.  Also place the ap in the same subnet as the wlc management.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
New Member

Re: AP3602E not join with remote 5508

Is not possible that the AP is on the same subnet as the WLC. The AP is in a remote office and the WLC at the central office, communicating via an MPLS.

Hall of Fame Super Silver

Re: AP3602E not join with remote 5508

Okay... well run the commands as I would like to see that in the output and then after the AP gets a valid ip address, issue the following

capwap ap controller ip address

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
New Member

Re: AP3602E not join with remote 5508

This is the output of AP

Thanks

Hall of Fame Super Silver

Re: AP3602E not join with remote 5508

Don't run the debug.... how many AP's do you have there that is joined to the WLC?

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
New Member

Re: AP3602E not join with remote 5508

What debug not want me to run?

There are no AP joined in the WLC, this is a new installation.

Thanks

Hall of Fame Super Silver

Re: AP3602E not join with remote 5508

Don't run this...debug capwap client event  I want to see the AP try to find and show a fail and reboot again.

Since this is a new install, then maybe you have something blocking UDP 5246 and UDP 5247.  I though there were other APs up and you only had issue with this one.  The only other way to see if something is blocking is to ship the AP back and connect it on the same subnet as the WLC.  If that joins fine, then send it back to the remote site.  If the AP doesn't join, then something is blocking or dropping those two ports.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
New Member

Re: AP3602E not join with remote 5508

I have another AP and the output is the same, do not think it's a hardware problem in AP.

Thanks.

Hall of Fame Super Silver

Re: AP3602E not join with remote 5508

It's not a hardware problem... there is something blocking the upd ports for the join.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver

Re: AP3602E not join with remote 5508

You need to also let the log runs... there is more info that needs to be shown... let it go for like 5 minutes or so.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
New Member

Re: AP3602E not join with remote 5508

Debug any specific or just the connection to the console.

Thanks.

Hall of Fame Super Silver

Re: AP3602E not join with remote 5508

No debug... just capture the output from the console, reboot the AP and let that run for 5+ minutes.

-Scott
*** Please rate helpful posts ***
New Member

Re: AP3602E not join with remote 5508

This debug is of 10 minutes.

And this debug is the switch where is connected the ap

C2960X#

Jan 29 23:46:06.690: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:46:06.690: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:46:16.690: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:46:16.690: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:46:26.687: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:46:26.687: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:46:36.688: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:46:36.691: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:46:46.024: UDP: rcvd src=10.180.0.17(123), dst=10.180.41.2(123), length=56

Jan 29 23:46:46.688: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:46:46.688: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:46:56.689: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:46:56.689: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:47:06.686: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:47:06.689: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:47:16.686: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:47:16.690: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:47:26.687: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:47:26.687: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:47:36.683: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:47:36.687: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:47:46.684: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:47:46.687: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:47:51.029: UDP: rcvd src=10.180.0.17(123), dst=10.180.41.2(123), length=56

Jan 29 23:47:56.684: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:47:56.684: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:48:06.685: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:48:06.685: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:48:16.685: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:48:16.685: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:48:26.686: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:48:26.686: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:48:36.683: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:48:36.683: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:48:46.683: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:48:46.683: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:48:56.040: UDP: rcvd src=10.180.0.17(123), dst=10.180.41.2(123), length=56

Jan 29 23:48:56.684: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:48:56.684: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:49:06.684: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:49:06.684: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:49:16.684: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:49:16.684: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:49:26.685: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:49:26.685: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:49:36.685: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:49:36.685: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:49:46.686: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:49:46.686: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:49:56.686: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:49:56.686: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:49:59.035: UDP: rcvd src=10.180.0.17(123), dst=10.180.41.2(123),

Jan 29 23:50:06.687: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:50:06.687: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246),

Jan 29 23:50:16.687: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:50:16.687: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223),

Jan 29 23:50:26.687: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:50:26.687: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246),

Jan 29 23:50:36.677: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:50:36.677: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:50:46.678: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:50:46.678: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:50:56.678: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:50:56.678: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:51:04.047: UDP: rcvd src=10.180.0.17(123), dst=10.180.41.2(123), length=56

Jan 29 23:51:06.675: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:51:06.679: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:51:16.675: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:51:16.675: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:51:26.676: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:51:26.679: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:51:36.676: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:51:36.676: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:51:46.677: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:51:46.677: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:51:56.674: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:51:56.674: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:52:06.674: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:52:06.674: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:52:07.041: UDP: rcvd src=10.180.0.17(123), dst=10.180.41.2(123), length=56

Jan 29 23:52:16.674: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:52:16.674: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:52:26.671: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:52:26.675: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:52:36.672: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:52:36.672: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:52:46.672: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:52:46.672: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:52:56.673: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:52:56.673: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:53:06.670: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:53:06.673: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:53:11.053: UDP: rcvd src=10.180.0.17(123), dst=10.180.41.2(123), length=56

Jan 29 23:53:16.670: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:53:16.670: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:53:26.671: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:53:26.674: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:53:36.671: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:53:36.671: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:53:46.671: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:53:46.671: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:53:56.668: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:53:56.668: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:54:06.669: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:54:06.669: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:54:16.669: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:54:16.669: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:54:18.057: UDP: rcvd src=10.180.0.17(123), dst=10.180.41.2(123), length=56

Jan 29 23:54:26.670: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:54:26.670: UDP: rcvd src=10.180.41.21(36135), dst=255.255.255.255(5246), length=131

Jan 29 23:54:36.667: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Jan 29 23:54:36.667: UDP: rcvd src=10.180.41.21(36134), dst=255.255.255.255(12223), length=98

Thanks.

Hall of Fame Super Silver

AP3602E not join with remote 5508

That output didn't have much... oh well...

How many AP's do you have up on your WLC?  From this site to the site the WLC is at, you are not using NAT are you?

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
VIP Purple

Re: AP3602E not join with remote 5508

HI,

As per yor Logs:

*spamApTask0: Jan 29 18:47:03.491: c0:67:af:28:d2:64 Received LWAPP DISCOVERY REQUEST to e4:c7:22:ab:28:80 on port '2'

*spamApTask0: Jan 29 18:47:03.491: c0:67:af:28:d2:64 Discarding discovery request in LWAPP from AP supporting CAPWAP

you are using..Layer 2 LWAPP WLC Discovery Algorithm

Your Management IP(10.180.5.3) and AP IP(10.180.41.16) is in diffirent subnet

Try to use AP and WLC in same subnet and then try again.

Reagrds

New Member

AP3602E not join with remote 5508

Hi sandeepchoudhary21,

We are using Layer 3 LWAPP WLC Discovery Algorithm with option 43 in the DHCP that I have mounted swtich where the AP is connected

Thanks.


VIP Purple

AP3602E not join with remote 5508

Can you ping the AP from WLC ???

Also paste the output of these commands:

debug capwap event enable or debug lwapp event enable or


debug pm pki enable

Regards

VIP Purple

Re: AP3602E not join with remote 5508

First of all make sure your AP can reach 5508 management IP. Go to AP console (once it obtained IP via DHCP) & then ping WLC mgt IP address.

*Jan 24 11:45:07.211: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C2960X-24PS-L (c414.3cad.e801)

*Jan 24 11:45:21.771: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.180.41.20, mask 255.255.255.0, hostname APc067.af28.d264

Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.180.32.19) (10.180.32.17) [OK]

*Jan 24 11:45:32.655: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.180.5.3 obtained through DHCP

*Jan 24 11:45:32.655: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

Through your log msg we can see 10.180.5.3 is the WLC IP learn by AP via DHCP option 43. Is it the one you configured on your 5508 ? (show interface summary output of your WLC will prove this)

Also you have PoE issue where all radio get disabled due to low power available via your 2960. That to be fixed as well

HTH

Rasika

**** Pls rate all useful responses ****

New Member

AP3602E not join with remote 5508

Hi,

I can ping from the AP to the WLC and the WLC from AP.

(Cisco Controller) >show interface summary

Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Gu                                                                             est

-------------------------------- ---- -------- --------------- ------- ------ --                                                                             ---

management                       2    untagged 10.180.5.3      Static  Yes    No                                                                            

service-port                     N/A  N/A      10.180.2.5      Static  No     No                                                                            

virtual                          N/A  N/A      1.1.1.1         Static  No     No

446
Views
0
Helpful
31
Replies
CreatePlease login to create content