Hello and thanks in advance for any assistance in this matter. I'm trying to configure a wireless connection on a Cisco 1811w router. The way it is now I can see the wireless lan and I can connect to it after entering the wep key but DHCP (I assume) is not working. No wireless client can get an ip address. I also want to change the authentication from wep to wpa-psk which I did at one point but I went back to the old config since it did the same thing.
!version 12.4 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname XXXXXXX ! boot-start-marker boot-end-marker ! no logging console enable secret XXXXXXXXXXXXXXXXXXXXXX. ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common ! [output cut] ! ! [output cut] ! ! crypto isakmp policy 1 encr 3des authentication pre-share group 2 crypto isakmp key XXXXXXXX address [cut] crypto ipsec transform-set myset esp-3des esp-sha-hmac ! crypto map vpn 1 ipsec-isakmp set peer [cut] set transform-set myset match address 100 ! ! dot11 ssid LEWY authentication open guest-mode ! ! ! no ip dhcp use vrf connected ! ip dhcp pool [cut] network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server [cut] ! ! ip cef no ip domain lookup ip domain name [cut] no ipv6 cef ! multilink bundle-name authenticated ! ![cut] archive log config hidekeys ! ! ip ssh version 2 bridge irb ! ! ! interface FastEthernet0 ip address [cut] 255.255.255.240 ip nat outside ip virtual-reassembly ip tcp adjust-mss 1300 duplex auto speed auto crypto map vpn ! interface FastEthernet1 no ip address shutdown duplex auto speed auto ! interface FastEthernet2 ! interface FastEthernet3 ! interface FastEthernet4 ! interface FastEthernet5 ! interface FastEthernet6 ! interface FastEthernet7 ! interface FastEthernet8 ! interface FastEthernet9 ! interface Dot11Radio0 no ip address ! encryption key 1 size 128bit 7 XXXXXXXXXXXXXXXXXXXXXXXX transmit-key encryption mode wep mandatory ! ssid LEWY ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root access-point bridge-group 10 bridge-group 10 subscriber-loop-control bridge-group 10 spanning-disabled bridge-group 10 block-unknown-source no bridge-group 10 source-learning no bridge-group 10 unicast-flooding ! interface Dot11Radio1 no ip address speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0 station-role root access-point ! interface Vlan1 no ip address ip tcp adjust-mss 1300 bridge-group 10 bridge-group 10 spanning-disabled ! interface Async1 no ip address encapsulation slip ! interface BVI10 ip address 192.168.1.1 255.255.255.0 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1300 ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 [cut]! ! ip http server ip http authentication local ip http secure-server ip nat inside source route-map NONAT interface FastEthernet0 overload ip nat inside source static tcp 192.168.1.70 3391 [cut] 3391 extendable ! access-list 100 permit ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 access-list 2699 deny ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 access-list 2699 permit ip any any ! ! ! route-map NONAT permit 10 match ip address 2699 ! ! ! ! control-plane ! bridge 10 route ip ! line con 0 line 1 modem InOut stopbits 1 speed 115200 flowcontrol hardware line aux 0 line vty 0 4 password 7 xxxxxxxxxxxxxxxxxxxx login authentication local transport input telnet ssh line vty 5 193 password 7 xxxxxxxxxxxxxxxxxxxxx login authentication LOCAL !
Transferring Crash file from standby:
Login to the Active WLC in HA.
(Cisco Controller) >transfer upload datatype crash
(Cisco Controller) >transfer upload filename <Desired filename>
(Cisco Controller) >transfer up...
This is the start of a display filter cross reference between Wireshark and OmniPeek.
The 1st installment is a table of advanced filters. More filters will be added as time allows.
It is a living doc, so check back for changes every so often
Please feel ...
I have created a Powershell script to automatically add a Wireless Guest User on Cisco WLCs. (tested on 2500 Series)
The script should be completely self explanatory.
Powershell SNMP Module (Install-Module -Name SNMP)
SNMP Write Access to...