02-07-2014 04:00 AM - edited 07-05-2021 12:07 AM
Hello,
We have WiSM for WLAN deployed in our premises and we are going to open a new branch. I was thinking to install a Cisco 897VA router in the new branch but I would like centralised wireless management managed by the WiSM controller. My question is if WiSM supports the AP on the Cisco 897VA router and if it is going to be supported in the 5508 and 2504 controllers as well.
TIA,
Nicos Nicolaides
Solved! Go to Solution.
02-07-2014 05:19 AM
Controller software release 7.0.116.0 or later releases support the embedded access points: AP801 and AP802, which are the integrated access points on the Cisco 880 Series Integrated Services Routers (ISRs).
You have wism right, which version ?
Check the matrix again AP 801 and AP 802 is supported, its depends on the version you have your WLC.
Reagrds
Dont forget to arte helpful posts
02-07-2014 04:11 AM
Hi,
I never used this router for connection to AP.
May be this is not you want the answer but still.....
But i will recomamnd you to use HREAP
H-REAP is a wireless solution for branch office and remote office deployments. H-REAP enables us to configure and control access points (APs) in a branch or remote office from the corporate office through a WAN link without deploying a controller in each office.
Make sure:
H-REAP is supported only on:
1130AG, 1140, 1240, 1250, 1260, AP801, AP 802, 1040, and AP3550 APs
Cisco 5500, 4400, 2100, 2500, and Flex 7500 Series Controllers
Catalyst 3750G Integrated Controller Switch
Catalyst 6500 Series Wireless Services Module (WiSM)
Wireless LAN Controller Module (WLCM) for Integrated Services Routers (ISRs)
Here are the diff modes and config setails.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807cc3b8.shtml
Reagrds
Dont forget to rate helpful posts
02-07-2014 04:15 AM
As per this datasheet:
It supports the AP connected to this router.
http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78-519930.html
The 8-port 10/100 Fast Ethernet managed switch offers VLAN support and 4-port support for Power over Ethernet (PoE) (optional for certain models) to power IP phones or external access points.
Reagrds
Dont forget to arte helpful posts
02-07-2014 05:04 AM
We are planning to use H-REAP for corporate access, but i dont see it anywhere in the compatibility matrix.
Is there any official answer?
02-07-2014 05:19 AM
Controller software release 7.0.116.0 or later releases support the embedded access points: AP801 and AP802, which are the integrated access points on the Cisco 880 Series Integrated Services Routers (ISRs).
You have wism right, which version ?
Check the matrix again AP 801 and AP 802 is supported, its depends on the version you have your WLC.
Reagrds
Dont forget to arte helpful posts
02-07-2014 05:22 AM
Thanks, this is what i wanted to verify.
02-07-2014 05:24 AM
Glad to help.
Regards
Sent from Cisco Technical Support iPhone App
02-07-2014 04:54 PM
I've got about 12 890W and all their APs are joined to the WiSM-2s running 7.6.X code.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide