Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cisco Aiornet 1042 with MAC address

Hi,

I have a Cisco Aiornet, model  AIR-AP1042N-E-K9.

I need to configure the AP to only certain MAC access. 
I'm doing the configuration through the console. 
The wireless network is not showing up in devices, anyone know why?

 

version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap_disi
!
!
logging rate-limit console 9
enable secret 5 xxxxx.
!
aaa new-model
!
!
aaa group server radius rad_eap
!
aaa group server radius rad_mac
!
aaa group server radius rad_acct
!
aaa group server radius rad_admin
!
aaa group server tacacs+ tac_admin
!
aaa group server radius rad_pmip
!
aaa group server radius dummy
!
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local 
aaa accounting network acct_methods start-stop group rad_acct
!
!
!
!
!
aaa session-id common
no ip routing
no ip cef
!
!
!
!
dot11 syslog
!
dot11 ssid DISI-WLAN24
   authentication open 
!
dot11 ssid DISIWIFI
   authentication open mac-address mac_methods 
   authentication key-management wpa version 2
   infrastructure-ssid
!
!
dot11 guest
!
!
!
username Cisco password 7 xxxx
username Admin privilege 15 password 7 xxxx
!
!
bridge irb
!
!
!
interface Dot11Radio0
 no ip address
 no ip route-cache
 !
 encryption mode ciphers aes-ccm 
 !
 ssid DISI-WLAN24
 !
 ssid DISIWIFI
 !
 antenna gain 0
 speed  basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
 station-role root
 l2-filter bridge-group-acl
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 spanning-disabled
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
!
interface Dot11Radio1
 description AP SITAS
 no ip address
 no ip route-cache
 !
 encryption mode ciphers aes-ccm 
 !
 ssid DISIWIFI
 !
 antenna gain 0
 peakdetect
 no dfs band block
 speed  basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
 channel dfs
 station-role root
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 spanning-disabled
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
 no ip address
 no ip route-cache
 duplex auto
 speed auto
 l2-filter bridge-group-acl
 no keepalive
 bridge-group 1
 bridge-group 1 spanning-disabled
 no bridge-group 1 source-learning
!
interface BVI1
 ip address 192.168.0.252 255.255.254.0
 no ip route-cache
 ipv6 address dhcp
 ipv6 address autoconfig
 ipv6 enable
!
ip default-gateway 192.168.1.254
ip forward-protocol nd
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1 
!
access-list 700 permit 8830.8a24.7eb5   0000.0000.0000
access-list 700 deny   0000.0000.0000   ffff.ffff.ffff
!
snmp-server view dot11view ieee802dot11 included
snmp-server community public view dot11view RO
snmp-server location DISI
snmp-server contact SITAS
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps entity
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps dot11-qos
snmp-server enable traps switch-over
snmp-server enable traps rogue-ap
snmp-server enable traps wlan-wep
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server enable traps cpu threshold
snmp-server enable traps aaa_server
snmp-server host 192.168.1.6 public 
radius-server attribute 32 include-in-access-req format %h
radius-server vsa send accounting
!
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
 transport input all
!
sntp server 192.168.1.215
sntp broadcast client
end

Everyone's tags (1)
2 REPLIES
Hall of Fame Super Gold

Configuring MAC ACL

Bronze

Please refer: http://www

Please refer: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/12-4-25d-JA/Configuration/guide/cg_12_4_25d_JA/scg12-4-25d-JA-chap16-filters.html#wp1034897

31
Views
0
Helpful
2
Replies