Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

H-REAP vlan template?

Is there a way to set-up the locally switched H-REAP vlan(s) via WCS template?

Thanks!

14 REPLIES
Hall of Fame Super Silver

Re: H-REAP vlan template?

I know in WCS v6.0.181.0 you can set the native vlan and the ssid to vlan mappings.  What version are you running?

-Scott
*** Please rate helpful posts ***
New Member

Re: H-REAP vlan template?

I'm currently running WCS 6.0.132.0+

I've been looking for a template to set the H-REAP vlan mappings, rather than doing it per AP.  Either I'm not finding it or 6.0.132.0 doesn't support it.

May be time to upgrade.

Thanks.

Hall of Fame Super Silver

Re: H-REAP vlan template?

You create a template and have to apply it to an AP oR multiple AP's

-Scott
*** Please rate helpful posts ***
New Member

Re: H-REAP vlan template?

On the AP parameters tab, in the LW AP template detail I can enable H-REAP and select a native vlan but the Profile Name - VLAN mappings area doesn't take input or offer a option to set or select local vlan IDs.

I'll dig up the release notes on the newer version of WCS.

Hall of Fame Super Silver

Re: H-REAP vlan template?

Refresh config from controller... You have ap's in H-REAP mode?

-Scott
*** Please rate helpful posts ***
Cisco Employee

Re: H-REAP vlan template?

Did you click the "Show All Profile-Mapping"?  Or is this still not what you are looking for?

New Member

Re: H-REAP vlan template?

When I click that, nothing gets populated.  I've already got half a dozen H-REAP sites with different native and local vlans.  I'm just looking for a way to do groups of APs, rather than one at a time.

I'll refresh the configs again.

Hall of Fame Super Silver

Re: H-REAP vlan template?

Do your SSIDs show up there

-Scott
*** Please rate helpful posts ***
New Member

Re: H-REAP vlan template?

Nope, even after refreshing configs from controllers, retaining template associations.

Hall of Fame Super Silver

Re: H-REAP vlan template?

Can you post a screen shot

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver

Re: H-REAP vlan template?

Here is what I see on my lab WCS... I check H-REAP/REAP Configuration, then click on Show All Profile-Mapping.

-Scott
*** Please rate helpful posts ***
New Member

Re: H-REAP vlan template?

Thanks for the screen shots.  I took off early Friday.

My screen shots would look like your first one.  Unlike your second one, I never see anything in the Profiles box.

Perhaps I'm shooting myself in the foot using the same SSID at the H-REAP sites as at the centrally switched sites.  The difference being the H-REAP WLANs are mapped to the management interface but with traffic dumped onto a locally routed/switched vlan.  Strange though, not one SSID shows up in the profiles box.

I would expect to see multiples of the same SSID with differing locally switched vlan numbers corresponding to local vlans at the different H-REAP sites.

Hall of Fame Super Silver

Re: H-REAP vlan template?

That would not matter... my ssid's are also set on AP's that are centrally switched so I don't know why your mappings don't show up.

-Scott
*** Please rate helpful posts ***
New Member

Re: H-REAP vlan template?

Go to:

Configure >  Controller Template Launch Pad >  WLANs >  WLAN Configuration

Select a WLAN that you want to show up in the profiles box.

Go to the Advanced Tab and check the box next to H-REAP Local Switching.

The WLAN will now show up in the profiles box in the AP Template.

771
Views
0
Helpful
14
Replies
CreatePlease to create content