Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

Cisco Employee

How to SnmpWalk a WLC running SNMP v3? What am I doing wrong...

'having syntax difficulties trying to SNMPwalk a WLC with SNMP v3 setup on it

Setttings are::

v3 user is prime

HMAC-SHA Auth Password = BBis123!ATis123

CFB-AES-128 Privacy Protocol = BBis123!ATis123

host 192.168.169.200

ade # snmpwalk -v3 -u prime -l AuthPriv -a sha -A 'BBis123!ATis123' -x AES -X 'BBis123!ATis123' 192.168.169.200

snmpwalk: Timeout

ade #

what am I doing wrong?  ahhhh

1 ACCEPTED SOLUTION

Accepted Solutions
VIP Purple

Re: How to SnmpWalk a WLC running SNMP v3? What am I doing wron

Have you enabled SNMPv3 under Management -> SNMP -> General?

Then it should work that way:

schlipp:~ karsten$ snmpwalk -v3 -u zenoss -l AuthPriv -a sha -A zzzz -x AES -X 'xxxx' 10.10.10.220

SNMPv2-MIB::sysDescr.0 = STRING: Cisco Controller

SNMPv2-MIB::sysObjectID.0 = OID: SNMPv2-SMI::enterprises.9.1.1279

DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (855721800) 99 days, 1:00:18.00

...

-- 
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni


--
Don't stop after you've improved your network! Improve the world by lending money to the working poor: http://www.kiva.org/invitedby/karsteni
4 REPLIES
VIP Purple

Re: How to SnmpWalk a WLC running SNMP v3? What am I doing wron

Have you enabled SNMPv3 under Management -> SNMP -> General?

Then it should work that way:

schlipp:~ karsten$ snmpwalk -v3 -u zenoss -l AuthPriv -a sha -A zzzz -x AES -X 'xxxx' 10.10.10.220

SNMPv2-MIB::sysDescr.0 = STRING: Cisco Controller

SNMPv2-MIB::sysObjectID.0 = OID: SNMPv2-SMI::enterprises.9.1.1279

DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (855721800) 99 days, 1:00:18.00

...

-- 
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni


--
Don't stop after you've improved your network! Improve the world by lending money to the working poor: http://www.kiva.org/invitedby/karsteni
Cisco Employee

Re: How to SnmpWalk a WLC running SNMP v3? What am I doing wron

karsten,

thanks for your response.  i however got all busy today and wasn't even able to look at my controller to see if v3 was enabled or not.....duh, didn't even think of that!!!

i'll take a look 1st thing in AM and will let you know.

Cisco Employee

Re: How to SnmpWalk a WLC running SNMP v3? What am I doing wron

that was it karsten-

thanks man!!!

VIP Purple

Re: How to SnmpWalk a WLC running SNMP v3? What am I doing wron

sometimes it's that easy ... ;-)

-- 
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni


--
Don't stop after you've improved your network! Improve the world by lending money to the working poor: http://www.kiva.org/invitedby/karsteni
449
Views
0
Helpful
4
Replies