Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

MBP dropping connecting on 887w

I have a 887w with intergrated wireless and it keeps on dropping my macbook pro.

Below is the configuration.

Any thing that is glaring that I should change?

[code]

Building configuration...

Current configuration : 2884 bytes

!

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname ap

!

logging rate-limit console 9

enable secret 5 $1$3It1$NoWM5fCF87TM//gLz1Npq.

!

no aaa new-model

!

!

dot11 syslog

!

dot11 ssid Colts-2006

   authentication open

   authentication key-management wpa version 2

   guest-mode

   wpa-psk ascii 0 [password]

!

!

!

username cisco privilege 15 secret 5 $1$15se$qlcsjqiD02G9U.nnzjxWm.

!

!

ip scp server enable

bridge irb

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

encryption mode ciphers aes-ccm tkip

!

ssid Colts-2006

!

antenna gain 0

station-role root access-point

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!        

interface GigabitEthernet0

description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router

no ip address

no ip route-cache

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

!

interface BVI1

ip address 192.168.100.5 255.255.255.0

no ip route-cache

!

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

bridge 1 route ip

!

!

banner exec ^CC

% Password change notice.

-----------------------------------------------------------------------

Default username/password setup on AP is cisco/cisco with privilege level 15.

It is strongly suggested that you create a new username with privilege level

15 using the following command for console security.

username <myuser> privilege 15 secret 0 <mypassword>

no username cisco

Replace <myuser> and <mypassword> with the username and password you want to

use. After you change your username/password you can turn off this message

by configuring  "no banner login" and "no banner exec" in privileged mode.

-----------------------------------------------------------------------

^C

banner login ^CC

% Password change notice.

-----------------------------------------------------------------------

Default username/password setup on AP is cisco/cisco with privilege level 15.

It is strongly suggested that you create a new username with privilege level

15 using the following command for console security.

username <myuser> privilege 15 secret 0 <mypassword>

no username cisco

Replace <myuser> and <mypassword> with the username and password you want to

use. After you change your username/password you can turn off this message

by configuring  "no banner login" and "no banner exec" in privileged mode.

-----------------------------------------------------------------------

^C

!

line con 0

privilege level 15

login local

no activation-character

line vty 0 4

login local

!

cns dhcp

end

[/code]

4 REPLIES
Hall of Fame Super Silver

Re: MBP dropping connecting on 887w

Try only using AES-CCM... Should use TKIP with wpa2

encryption mode ciphers aes-ccm

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

MBP dropping connecting on 887w

awesome thank you.

However now my wifi is asking for username/password,

How do I do just a password key?

Hall of Fame Super Silver

Re: MBP dropping connecting on 887w

Delete the wireless profile from your MBP and click on the ssid again. It should ask you just for the password/pre shared key.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver

Re: MBP dropping connecting on 887w

By the way, since you made a change to the ssid, it might be better to remove all existing wireless profiles on your other devices also and create it again.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
149
Views
0
Helpful
4
Replies