Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

PoE injector needed for WAP4410N

I bought 2 WAP4410N wireless routers but it did not come with a PoE injector.  We do not have a PoE capable switch.  I have a couple of 3COM PoE injectors but am concerned about differing PoE standards could cause the 3Com PoE injector to damage the WAP4410N.

I cannot find a PoE injector on the Cisco website. Can anyone provide the Cisco part number for a PoE injector for the Cisco WAP4410N or provide assurances about the 3COM PoE that I have for the 3COM 3CRWER100-75 access points?

5 REPLIES
Hall of Fame Super Red

Re: PoE injector needed for WAP4410N

Hi Thomas,

The WAP4410N is IEEE802.3af PoE Compliant, so if the 3COM supports IEEE802.3af  PoE

you should be good to go

Here are the other recommended PoE injectors;

To link your wired network with your wireless network, connect the access point’s
Ethernet network port to any switch or router with Power over Ethernet (PoE)—or
a PoE injector, such as the Cisco WAPPOE or WAPPOE12.

http://ciscosystems.com/en/US/docs/wireless/access_point/csbap/wap4410n/administration/guide/WAP4410N_Admin_Guide.pdf

Here is an example of the PoE kit;

http://www.ipphone-warehouse.com/WAPPOE-Linksys-PoE-Kit-p/wappoe.htm

Cheers!

Rob

New Member

Re: PoE injector needed for WAP4410N

Rob,

Thank you very much for your quick response. This is exactly the

information that I needed!

Tom Vitt

Global Bid Manager,

IBM Corporation,

Sales Transaction Hub

Berlin, New Jersey 08009-2218

1-856-768-5868

tvitt@us.ibm.com / Tom Vitt/Mount Laurel/IBM@IBMUS

To learn more about the Sales Transaction Hub, Click Here (IBM Internal

Use)

From: "rob.huffman"

To: Tom Vitt/Mount Laurel/IBM@IBMUS

Date: 08/28/2010 12:51 PM

Subject: New message: "PoE

injector needed for WAP4410N"

Thomas Vitt,

A new message was posted in the Discussion thread "PoE injector needed for

WAP4410N":

https://supportforums.cisco.com/message/3168935#3168935

Author : rob.huffman

Profile : https://supportforums.cisco.com/people/rob.huffman

Message:

New Member

Re: PoE injector needed for WAP4410N

PoEInjector is a pretty good resource for any Power over Ethernet needs you have.

Do you need 10/100 or Gigabit? If its Wireless N you probably need GigE.

These links should help. Let me know if you have any more questions.

- Joe

New Member

Re: PoE injector needed for WAP4410N

I am also considering a PoE injector for the WAP4410N.

I am gravitating towards the WAPPOE12, however the item description seems to indicate it feeds 48V when you're just using it as an injector.

The WAP4410N manual seems to imply it needs just 12V when using PoE.

New Member

Re: PoE injector needed for WAP4410N

These guys make quite a few elegant solutions for providing power to both PoE and non-PoE devices over Cat-5 cabling:
http://www.panoptictechnology.com/network-smart-adapters/

11077
Views
0
Helpful
5
Replies
CreatePlease login to create content