Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Setting up additional Cisco 1142 AP

I am in the process of deploying an additional Cisco 1142 AP into my network. I would like to set it up to be the same SSID as the first one, and be able to have laptops roam from AP to AP. I am simply trying to expand the current coverage of my wireless network. I have both APs mounted and access to both.

CISCOAP01 - 192.168.2.2

CISCOAP02 - 192.168.2.3

What do I need to do (configre) to make this happen? I am rather new with Cicso. I am using the web interface to setup the APs. The first one has been up and running for about a year now with no problems. Here is the config file if that helps. Thanks

!

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname CISCOAP01

!

enable secret 5 $1$tnSs$0e9SFlxbMjocoevA5udaW/

!

no aaa new-model

!

!

dot11 syslog

!

dot11 ssid FEDCO

   authentication open

   authentication key-management wpa

   guest-mode

   wpa-psk ascii 7 110B160A04060E1E547B78

!

!

!

username Cisco password 7 00271A150754

!

!

bridge irb

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

encryption mode ciphers tkip

!

ssid FEDCO

!

antenna gain 0

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface Dot11Radio1

no ip address

no ip route-cache

shutdown

antenna gain 0

dfs band 3 block

channel dfs

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface GigabitEthernet0

no ip address

no ip route-cache

duplex auto

speed auto

no keepalive

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

!

interface BVI1

ip address 192.168.2.2 255.255.255.0

no ip route-cache

!

ip default-gateway 192.168.2.254

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

bridge 1 route ip

!

!

!

line con 0

line vty 0 4

login local

!

sntp server 192.168.2.249

sntp broadcast client

end

Everyone's tags (3)
1 ACCEPTED SOLUTION

Accepted Solutions

Re: Setting up additional Cisco 1142 AP

all you need to do is create the same SSID on your new AP. keep all the same ciphers and PSK and the clients should roam between them fine. You do t need any of the WLCCP commands as you are not doing 802.1x

Steve

Sent from Cisco Technical Support iPhone App

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
2 REPLIES

Re: Setting up additional Cisco 1142 AP

all you need to do is create the same SSID on your new AP. keep all the same ciphers and PSK and the clients should roam between them fine. You do t need any of the WLCCP commands as you are not doing 802.1x

Steve

Sent from Cisco Technical Support iPhone App

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

Setting up additional Cisco 1142 AP

Awesome! Thank you for your quick responce! Much appreciated for a Cisco n00b like me!

662
Views
0
Helpful
2
Replies
CreatePlease to create content