Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

WLC 2504 and AIRCAP2602 problem with registracion

Hi, 

today i have set up a small wireless network . I use cisco wlc 2504 and three ap AIR-CAP 2602. The problem that I have is that AP won't register with wlc. I doubt that the problem is with the certificate,but I am not sure. maybe problem is related to country code.I don't know. I can ping AP from controller but it will not join. LWAPP image version 7.6.120.0 ,

 This is log from AP:

 

Jun  7 01:59:24.679: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
Jun  7 01:59:24.679: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
Jun  7 01:59:34.679: %CAPWAP-3-ERRORLOG: Go join a capwap controller 
Aug 19 15:12:05.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.25 peer_port: 5246
Aug 19 15:12:07.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.25 peer_port: 5246
Aug 19 15:12:07.411: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.25
Aug 19 15:12:07.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
Aug 19 15:12:07.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
Aug 19 15:12:07.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
Aug 19 15:12:07.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 192.168.1.25
Aug 19 15:12:25.575: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(UNKNOWN_MESSAGE_TYPE (5)


Aug 19 15:12:25.575: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE

 

can someone help me with this problem?

2 ACCEPTED SOLUTIONS

Accepted Solutions
Cisco Employee

Please verify :http://www

VIP Purple

did you configured the IP

did you configured the IP helper command on SVI interface ?

check the DHCP proxy on wlc.

controller > Advanced > DHCP and enable the proxy setting.

 

Regards

Dont forget to rate helpful posts

6 REPLIES

Is the time set correctly on

Is the time set correctly on the WLC? There could be a problem with the date and time on the certificates used by the controller.

New Member

thanks foe replay. Time is ok

thanks foe replay.

 

Time is ok, clock andtime zone is the same on wlc and ap.

VIP Purple

can you paste the output oif

can you paste the output oif these commands:

sh version from AP:

sh sysinfo from WLC

 

also paste the complete bootup process from AP console.

 

Regards

New Member

thank all for help .problem

thank all for help .

problem was contry code.

 

But now I have another , when I connect to my network lap top does'n get IP address . Dhcp server iz running cisco router. .

 

VIP Purple

did you configured the IP

did you configured the IP helper command on SVI interface ?

check the DHCP proxy on wlc.

controller > Advanced > DHCP and enable the proxy setting.

 

Regards

Dont forget to rate helpful posts

Cisco Employee

Please verify :http://www

265
Views
0
Helpful
6
Replies
CreatePlease to create content