Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

ASA image upgrade

Need to upgrade my Cisco ASA-5510 image from asa821-k8.bin to asa903-k8.bin with the following License. Do I need to buy a new license with image upgrade ????

 

#sh version

 

 

Cisco Adaptive Security Appliance Software Version 8.2(1)

Device Manager Version 6.2(1)

 

 

Compiled on Tue 05-May-09 22:45 by builders

System image file is "disk0:/asa821-k8.bin"

Config file at boot was "startup-config"

 

 

TMN-5510 up 294 days 2 hours

 

 

Hardware:   ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz

Internal ATA Compact Flash, 256MB

BIOS Flash M50FW080 @ 0xffe00000, 1024KB

 

 

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)

                             Boot microcode   : CN1000-MC-BOOT-2.00

                             SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03

                             IPSec microcode  : CNlite-MC-IPSECm-MAIN-2.04

0: Ext: Ethernet0/0         : address is ***************************

1: Ext: Ethernet0/1         : address is ***************************

2: Ext: Ethernet0/2         : address is ***************************

3: Ext: Ethernet0/3         : address is ***************************

4: Ext: Management0/0       : address ****************************

5: Int: Internal-Data0/0    : address is *****************************

6: Int: Internal-Control0/0 : address is ****************************

 

Licensed features for this platform:

Maximum Physical Interfaces  : Unlimited

Maximum VLANs                : 100      

Inside Hosts                 : Unlimited

Failover                     : Active/Active

VPN-DES                      : Enabled  

VPN-3DES-AES                 : Enabled  

Security Contexts            : 2        

GTP/GPRS                     : Disabled 

SSL VPN Peers                : 2        

Total VPN Peers              : 250      

Shared License               : Disabled

AnyConnect for Mobile        : Disabled 

AnyConnect for Linksys phone : Disabled 

AnyConnect Essentials        : Disabled 

Advanced Endpoint Assessment : Disabled 

UC Phone Proxy Sessions      : 2        

Total UC Proxy Sessions      : 2        

Botnet Traffic Filter        : Disabled 

 

 

This platform has an ASA 5510 Security Plus license.

 

 

Serial Number: ***************************

Running Activation Key: ****************************************************************************

Configuration register is 0x1

Configuration last modified by enable_15 at 22:29:35.255 ****************** Fri Apr 4 2014

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------

Need help 

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
New Member

>Do I need to buy a new

>Do I need to buy a new license with image upgrade ????

NO

But check the:

1)

https://supportforums.cisco.com/document/48646/asa-83-upgrade-what-you-need-know

 

2) migrate the configuration from 8.21 to 9.03 asking cisco TAC help

 

 

 

4 REPLIES
New Member

>Do I need to buy a new

>Do I need to buy a new license with image upgrade ????

NO

But check the:

1)

https://supportforums.cisco.com/document/48646/asa-83-upgrade-what-you-need-know

 

2) migrate the configuration from 8.21 to 9.03 asking cisco TAC help

 

 

 

Thanks for the concise and

Thanks for the concise and concrete answer.smiley

Hall of Fame Super Silver

In addition to Roberto's

In addition to Roberto's correct answer...

Please note that your ASA 5510 with 256 MB of RAM would need an upgrade to 1 GB to run ASA 8.3 or later software.

This is documented here.

Thanks Sir!!!!

Thanks Sir!!!!

165
Views
5
Helpful
4
Replies
CreatePlease to create content