Solved: Getting Error Logs Every Minit's From 5k

balakrishnansenthil · ‎09-03-2012

Hi,

Am getting every minit's this below logs.........

Can i know why it's happening....

Please advice me....

Logs:
=====

2012 Sep 3 17:17:42 5k %ETHPORT-5-IF_UP: Interface Ethernet106/1/3 is up in mode access
2012 Sep 3 17:17:55 5k %ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet106/1/2 is down (Link failure)
2012 Sep 3 17:17:56 5k %ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet106/1/3 is down (Link failure)
2012 Sep 3 17:17:58 5k %ETHPORT-5-SPEED: Interface Ethernet106/1/2, operational speed changed to 1 Gbps
2012 Sep 3 17:17:58 5k %ETHPORT-5-IF_DUPLEX: Interface Ethernet106/1/2, operational duplex mode changed to Full
2012 Sep 3 17:17:58 5k %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet106/1/2, operational Receive Flow Contr
ol state changed to off
2012 Sep 3 17:17:58 5k %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet106/1/2, operational Transmit Flow Cont
rol state changed to on
2012 Sep 3 17:17:59 5k %ETHPORT-5-IF_UP: Interface Ethernet106/1/2 is up in mode access
2012 Sep 3 17:17:59 5k %ETHPORT-5-SPEED: Interface Ethernet106/1/3, operational speed changed to 1 Gbps
2012 Sep 3 17:17:59 5k %ETHPORT-5-IF_DUPLEX: Interface Ethernet106/1/3, operational duplex mode changed to Full
2012 Sep 3 17:17:59 5k %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet106/1/3, operational Receive Flow Contr
ol state changed to off
2012 Sep 3 17:17:59 5k %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet106/1/3, operational Transmit Flow Cont
rol state changed to on
2012 Sep 3 17:17:59 5k %ETHPORT-5-IF_UP: Interface Ethernet106/1/3 is up in mode access
NX5K005#
=====================================================

NX5K005# sh running-config | b Ethernet106/1/2
interface Ethernet106/1/2

interface Ethernet106/1/3

interface Ethernet106/1/4
description MSSQL01
switchport access vlan 3838
spanning-tree port type edge

interface Ethernet106/1/5
description BCKUP01
switchport access vlan 3200
spanning-tree port type edge
=======================================================
show vpc brief

vPC Peer-link status
---------------------------------------------------------------------
id   Port   Status Active vlans
--   ----   ------ --------------------------------------------------
1    Po130 up     1,700-701,798,920-923,1100-1103,1105-1108,1110-111
                   3,1115-1118,1120-1123,1125-1128,1130-1133,1135-113
                   8,1140,1145,1150,1155,1160,1165,1300-1303,1305-130
                   8,1310-1313,1315-1318,1320-1323,1325-1328,1330-133
                   3,1335-1338,1340,1345,1350,1355,1360,1365,1500-150   ....

vPC status
----------------------------------------------------------------------------
id     Port        Status Consistency Reason                     Active vlans
------ ----------- ------ ----------- -------------------------- -----------
13     Po13        up     success     success                    1,700-701,7
                                                                 98,920-923,
                                                                 1100-1103,1
                                                                 105-1108,11
                                                                 10-1113....
105    Po105       up     success     success                    -
106    Po106       up     success     success                    -
106496 Eth105/1/1 up     success     success                    3830

106497 Eth105/1/2 up success success 1

106498 Eth105/1/3 up success success 1

106499 Eth105/1/4 up success success 3838

107520 Eth106/1/1 up success success 3830

107521 Eth106/1/2 up success success 1

107522 Eth106/1/3 up success success 1

107523 Eth106/1/4 up success success 3838

Jerry Ye · ‎09-04-2012

These are not errors. Your hosts are bouncing. It might be up right now but it was bouncing. If it is a FEX issue, it will happen to all the interfaces in the same ASIC.

Regards,

jerry

View solution in original post

Jerry Ye · ‎09-03-2012

Something plugged into port E106/1/2 and E106/1/3 is bouncing. Those messages (I will not call those errors) are interface up/down events. Can you check if there are anything connected?

Regards,

jerry

balakrishnansenthil · ‎09-03-2012

Hi Jerry,

It's Connected with core switch 7k......Please check still am getting same error...

Cable : Fiber optic

I suspect problem in cable,kindly check and let me know if anything, you want any other logs....

Regards,

Senthil

Jerry Ye · ‎09-03-2012

Fiber to N7K? I am not 100% sure how you have your switches configured and connected. Yes, you can try to swap out the cable to see if it improves or not.

Regards,

jerry

balakrishnansenthil · ‎09-03-2012

Thanks i will check and let you know....

The one more switch also am getting Error Logs please check and let me know this link fluctuating when i see the "Shoe VPC" some time showing link down please see below logs.

advice me ASAP.

Error Logs:
===========

2012 Sep 4 10:22:42 NX5K %ETHPORT-5-IF_UP: Interface Ethernet107/1/2 is up in mode access
2012 Sep 4 10:23:52 NX5K %ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet107/1/2 is down (Link failure)
2012 Sep 4 10:23:55 NX5K %ETHPORT-5-SPEED: Interface Ethernet107/1/2, operational speed changed to 1 Gbps
2012 Sep 4 10:23:55 NX5K %ETHPORT-5-IF_DUPLEX: Interface Ethernet107/1/2, operational duplex mode changed to Full
2012 Sep 4 10:23:55 NX5K %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet107/1/2, operational Receive Flow Contro
l state changed to off
2012 Sep 4 10:23:55 NX5K %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet107/1/2, operational Transmit Flow Contr
ol state changed to on
2012 Sep 4 10:23:55 NX5K %ETHPORT-5-IF_UP: Interface Ethernet107/1/2 is up in mode access
2012 Sep 4 10:24:09 NX5K %ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet107/1/2 is down (Link failure)
2012 Sep 4 10:24:12 NX5K %ETHPORT-5-SPEED: Interface Ethernet107/1/2, operational speed changed to 1 Gbps
2012 Sep 4 10:24:12 NX5K %ETHPORT-5-IF_DUPLEX: Interface Ethernet107/1/2, operational duplex mode changed to Full
2012 Sep 4 10:24:12 NX5K %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet107/1/2, operational Receive Flow Contro
l state changed to off
2012 Sep 4 10:24:12 NX5K %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet107/1/2, operational Transmit Flow Contr
ol state changed to on
2012 Sep 4 10:24:13 NX5K %ETHPORT-5-IF_UP: Interface Ethernet107/1/2 is up in m

Show VPC:
===========

108544 Eth107/1/1 up success success 3830

108545 Eth107/1/2 down* failed      Consistency Check Not      -
                                      Performed
108546 Eth107/1/3 up     success     success                    1

108547 Eth107/1/4 up success success 3838

Within One Minit same link fluctuating:
=======================================

Show VPC:
========
108544 Eth107/1/1 up success success 3830

108545 Eth107/1/2 up success success 1

108546 Eth107/1/3 up success success 1

108547 Eth107/1/4 up success success 3838

Regards,

Senthil

Jerry Ye · ‎09-03-2012

Same story on port E107/1/2, it is bouncing, check your connection.

108545 Eth107/1/2 down* failed Consistency Check Not -

Performed

This output is normal when an interface is down under show vpc.

HTH,

jerry

balakrishnansenthil · ‎09-03-2012

Thanks Jerry....

Do you think is it cable problem(fiber optic)......

It mean if cable problem why it's happening only one VPC.....it should be problem in all traffic in this port correct....

Please reply ASAP.

Regards,

Senthil

Jerry Ye · ‎09-04-2012

It would be anything. Cable, configuration, bad hardware, etc. You need to eliminate one element at a time to find the bad component.

Regards,

jerry

balakrishnansenthil · ‎09-04-2012

Thanks jerry....

I will try, before that i want to makesure....

The same error logs am getting another 3 switches also....

Totally we are using 10 5K's in our concern.

Switch 5k-08--->Ethernet107/1/2---Fex 107.

Switch 5K-07--->Ethernet107/1/2---Fex 107.

Switch 5K-06--->Ethernet106/1/2---Fex 106.
--->Ethernet106/1/3---Fex 106.

Switch 5K-05--->Ethernet106/1/2---Fex 106.
--->Ethernet106/1/3---Fex 106.

Is there any FEX issue....Please be makesure........

These logs is it major Error or any important....But link is showing UP.

Thanks Jerry...

regards,
Senthil

Jerry Ye · ‎09-04-2012

These are not errors. Your hosts are bouncing. It might be up right now but it was bouncing. If it is a FEX issue, it will happen to all the interfaces in the same ASIC.

Regards,

jerry

balakrishnansenthil · ‎09-04-2012

Thanks Jerry.....

I will try to eliminate one element let it see...

Please jerry if anything let me know....i will do the test.

Regards,

SenthilKumar

balakrishnansenthil · ‎09-20-2012

Thanks man,

we shut the interface for while because there is no config both ends(server&switch)

Thanks for all......