Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Nexus 2232 TM uplink ports are they only for uplink use?

We have upgraded our N5K to support the new 2232TM, but now we face the issue that the 8 SFP+ ports are not visible in our config:

Nexus5010_1# sh  fex 103 det

FEX: 103 Description: 2KSRV02   state: Online

  FEX version: 5.0(3)N2(2a) [Switch version: 5.0(3)N2(2a)]

  FEX Interim version: 5.0(3)N2(2a)

  Switch Interim version: 5.0(3)N2(2a)

  Extender Model: N2K-C2232TM-10GE,  Extender Serial: FOC15262P7Q

  Part No: 73-13626-03

  Card Id: 164, Mac Addr: 30:e4:db:66:12:02, Num Macs: 64

  Module Sw Gen: 21  [Switch Sw Gen: 21]

  post level: complete

pinning-mode: static    Max-links: 1

  Fabric port for control traffic: Eth1/9

  Fabric interface state:

    Po103 - Interface Up. State: Active

    Eth1/9 - Interface Up. State: Active

    Eth1/10 - Interface Up. State: Active

  Fex Port        State  Fabric Port

       Eth103/1/1  Down       Po103

       Eth103/1/2  Down       Po103

       Eth103/1/3  Down       Po103

       Eth103/1/4  Down       Po103

       Eth103/1/5  Down       Po103

       Eth103/1/6  Down       Po103

       Eth103/1/7  Down       Po103

       Eth103/1/8  Down       Po103

       Eth103/1/9  Down       Po103

      Eth103/1/10  Down       Po103

      Eth103/1/11  Down       Po103

      Eth103/1/12  Down       Po103

      Eth103/1/13  Down       Po103

      Eth103/1/14  Down       Po103

      Eth103/1/15  Down       Po103

      Eth103/1/16  Down       Po103

      Eth103/1/17  Down       Po103

      Eth103/1/18  Down       Po103

      Eth103/1/19  Down       Po103

      Eth103/1/20  Down       Po103

      Eth103/1/21  Down       Po103

      Eth103/1/22  Down       Po103

      Eth103/1/23  Down       Po103

      Eth103/1/24  Down       Po103

      Eth103/1/25  Down       Po103

      Eth103/1/26  Down       Po103

      Eth103/1/27  Down       Po103

      Eth103/1/28  Down       Po103

      Eth103/1/29  Down       Po103

      Eth103/1/30  Down       Po103

      Eth103/1/31  Down       Po103

      Eth103/1/32  Down       Po103

They are not visible: neither with the "show fex" neither with the "show int status", we cannot configure them....?

Do you think it's possible to access these ports by another way and configure them to allow some hosts to connect on it or is their purpose exclusively UPLINK?

best regards,

Eric Gillis

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Nexus 2232 TM uplink ports are they only for uplink use?

Do you mean the Fabric interfaces? If yes, you cannot use those for any host connectivities.

HTH,

jerry

2 REPLIES
Cisco Employee

Nexus 2232 TM uplink ports are they only for uplink use?

Do you mean the Fabric interfaces? If yes, you cannot use those for any host connectivities.

HTH,

jerry

New Member

Nexus 2232 TM uplink ports are they only for uplink use?

ok, thank you for your answer.

1619
Views
0
Helpful
2
Replies
CreatePlease to create content