Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

No export command in Nexus 1010

Hi all,

We want to do a backup of a virtual-service-blade in a Nexus 1010. The document we are following is:

http://www.cisco.com/en/US/docs/switches/datacenter/nexus1000/sw/4_2_1_s_p_1_3/software/configuration/guide/n1010_vsvcs_cfg_7backup.html

What we are supposed to do fron this document is to create a file named export-import, to shutdown the primary o secondary virtual service blades, and after it, to execute the command "export primary" o "export secondary", depending on which vsb we want to export.

========= DETAILED STEP IN THE DOCUMENT ================

n1010-1(config-vsb-config)# export  secondary

Note: export started..

Note: please be patient..

Note: please be patient..

Note: please be patient..

Note: export  completed...n1010-1(config-vsb-config)#

====================================================

The problem is that this "export" command is not available in our nexus 1010.

=========== NEXUS 1010 ===============================

N1010-MGMT(config-vsb-config)# export secondary

                                 ^

% Invalid command at '^' marker.

N1010-MGMT(config-vsb-config)#

N1010-MGMT(config-vsb-config)#

N1010-MGMT(config-vsb-config)# ?

  description                 Virtual service blade description

  disksize                    Configure disk size

  enable                      Deploy/remove the virtual service blade

  interface                   Configure virtual service blade interface vlan

  no                          Negate a command or set its defaults

  numcpu                      Configure numcpu

  ramsize                     Configure ram size

  shutdown                    Start/stop the virtual service blade

  virtual-service-blade-type  Select the virtual service blade type

  end                         Go to exec mode

  exit                        Exit from command interpreter

  pop                         Pop mode from stack or restore from name

  push                        Push current mode to stack or save it under name

  where                       Shows the cli context you are in

=====================================================

The version of the nexus is the same than the document's one.

Document: 4.2(1)SP1(3) ==> Nexus 1010: version 4.2(1)SP1(2)

Software

  loader:    version unavailable [last: loader version not available]

  kickstart: version 4.2(1)SP1(2)

  system:    version 4.2(1)SP1(2)

  kickstart image file is: bootflash:/nexus-1010-kickstart-mz.4.2.1.SP1.2.bin

  kickstart compile time:  1/27/2011 14:00:00 [01/28/2011 01:14:35]

  system image file is:    bootflash:/nexus-1010-mz.4.2.1.SP1.2.bin

  system compile time:     1/27/2011 14:00:00 [01/28/2011 04:13:25]

Hardware

  cisco Nexus 1010 Chassis ("Cisco Nexus1010 Chassis")

   with 14665728 kB of memory.

  Processor Board ID T023D700201

We don't know which can be the problem, wheter it can be a bug in the software, or we are doing something wrong.

Thank you

1 REPLY
Cisco Employee

No export command in Nexus 1010

The export command was a new feature added in the 4.2(1)SP1(3) version of code. Your 1010 is one rev lower.

You'll need to upgrade the code on the 1010 to the latest code to get the export command.

The upgrade is pretty straight forward. Just download the code and follow the upgrade guide.

louis

421
Views
0
Helpful
1
Replies
CreatePlease to create content