Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

SNAsw: link to AS400 via EE

We are trying to activate a link between a Cisco 2851 and a AS400 (iSeries)

snasw cpname PRUEBA.SNASW

snasw port HPRLOOP hpr-ip Loopback0

snasw pdlog information

snasw dlctrace format analyzer

snasw event dlc

interface Loopback0

ip address 192.168.104.31 255.255.255.0

By debuging snasw we get the following messages, an finally the tipical mismatch XID error or retry count

debug snasw dlc

000206: Jun 13 10:38:16.152 MET: 255 @I000002 Out sz:0 XID Null

000207: Jun 13 10:38:16.152 MET: 256 @I000002 In sz:80 XID 3 PN PRUEBA.D0612AAA xid:

000208: Jun 13 10:38:16.152 MET: 257 @I000002 Out sz:100 XID 3 PN PRUEBA.SNASW xid:FFF00000

000209: Jun 13 10:38:16.156 MET: 258 @I000002 In sz:113 XID 3 NP PRUEBA.D0612AAA xid:

000210: Jun 13 10:38:16.156 MET: 260 @I000002 Out sz:131 XID 3 NP PRUEBA.SNASW xid:FFF00000

000211: Jun 13 10:38:16.160 MET: 261 @I000002 In sz:113 XID 3 NP PRUEBA.D0612AAA xid:

000212: Jun 13 10:38:16.160 MET: 262 @I000002 Out sz:131 XID 3 NP PRUEBA.SNASW xid:FFF00000

000213: Jun 13 10:38:31.156 MET: 263 @I000002 In sz:113 XID 3 NP PRUEBA.D0612AAA xid:

000214: Jun 13 10:38:31.160 MET: 264 @I000002 Out sz:131 XID 3 NP PRUEBA.SNASW xid:FFF00000

000215: Jun 13 10:38:46.157 MET: 265 @I000002 In sz:113 XID 3 NP PRUEBA.D0612AAA xid:

000216: Jun 13 10:38:46.157 MET: 266 @I000002 Out sz:131 XID 3 NP PRUEBA.SNASW xid:FFF00000

000217: Jun 13 10:39:01.157 MET: 267 @I000002 In sz:113 XID 3 NP PRUEBA.D0612AAA xid:

000218: Jun 13 10:39:01.157 MET: 268 @I000002 Out sz:131 XID 3 NP PRUEBA.SNASW xid:FFF00000

000219: Jun 13 10:39:01.157 MET: %SNASW-3-CS_LOG_6: PROBLEM - 9 - XID protocol error during activation exchange

XID protocol error during activation exchange

Sense code             = 0x083E0000

Port name              = HPRLOOP

LS name                = @I000003

Adjacent CP name       = PRUEBA.D0612B9B

Remote MAC+SAP address =

Byte offset            = 0x00

Bit offset             = 0x00

The Cisco is running c2800nm-adventerprisek9_sna-mz.124-25f.bin      

There is a way to change the XID in the exchange between the Cisco and AS400?

1 REPLY
New Member

Re: SNAsw: link to AS400 via EE

The problem has been solved by applying PTFs to the AS400.

The router´s  configuration is ok.

Thanks.

516
Views
0
Helpful
1
Replies
CreatePlease to create content