Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Can't connect VPN WRVS4400N to Cisco800

Hello,

I'm connected from home to my office in VPN. The office router is a Cisco800.

I just replaced at home my BEFSX41 VPN router with the WRVS4400N V2 but I can't connect to my office.

There was no problem with the BEFSX41 in VPN, and I encoded the same configuration in the WRVS4400N. The status stays DOWN...

This is the VPN log:

Mar  8 09:35:04  - [VPN Log]: "dvc": terminating SAs using this connection
Mar  8 09:35:04  - [VPN Log]: "dvc" #1: deleting state (STATE_MAIN_I3)
Mar  8 09:35:08  - [VPN Log]: "dvc" #2: initiating Main Mode
Mar  8 09:35:08  - [VPN Log]: "dvc" #2: received Vendor ID payload [RFC 3947] method set to=109
Mar  8 09:35:08  - [VPN Log]: "dvc" #2: enabling possible NAT-traversal with method 3
Mar  8 09:35:08  - [VPN Log]: "dvc" #2: transition from state STATE_MAIN_I1 to state STATE_MAIN_I2
Mar  8 09:35:08  - [VPN Log]: "dvc" #2: STATE_MAIN_I2: sent MI2, expecting MR2
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: received Vendor ID payload [Cisco-Unity]
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: received Vendor ID payload [Dead Peer Detection]
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: ignoring unknown Vendor ID payload [64049a064ce182734231be596e3f231c]
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: received Vendor ID payload [XAUTH]
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: I did not send a certificate because I do not have one.
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: NAT-Traversal: Result using 3: peer is NATed
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: transition from state STATE_MAIN_I2 to state STATE_MAIN_I3
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: STATE_MAIN_I3: sent MI3, expecting MR3
Mar  8 09:35:09  - [VPN Log]: | protocol/port in Phase 1 ID Payload is 17/0. accepted with port_floating NAT-T
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: Main mode peer ID is ID_IPV4_ADDR: '192.168.254.2'
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: we require peer to have ID '91.183.hidden*.hidden*', but peer declares '192.168.254.2'
Mar  8 09:35:09  - [VPN Log]: "dvc" #2: sending encrypted notification INVALID_ID_INFORMATION to 91.183.hidden*.hidden*:4500

*Hidden by me

If seems something block...

What is "but peer declares '192.168.254.2"

Any ideas?

Thank you.

Pierre

  • Small Business Routers
410
Views
0
Helpful
0
Replies
This widget could not be displayed.