Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

IP Routing issue?

I am not sure what I am missing, but I have an IP that does not want to route.

Gateway of last resort is 192.168.3.14 to network 0.0.0.0

S*    0.0.0.0/0 [1/0] via 192.168.3.14
S     192.168.1.0/24 [1/0] via 192.168.23.1
      192.168.3.0/24 is variably subnetted, 2 subnets, 2 masks
C        192.168.3.0/24 is directly connected, GigabitEthernet0/1.1
L        192.168.3.21/32 is directly connected, GigabitEthernet0/1.1
S     192.168.4.0/24 [1/0] via 192.168.23.1
S     192.168.5.0/24 [1/0] via 192.168.23.1
S     192.168.10.0/24 [1/0] via 192.168.23.1
      192.168.21.0/30 is subnetted, 1 subnets
S        192.168.21.0 [1/0] via 192.168.23.1
      192.168.23.0/24 is variably subnetted, 2 subnets, 2 masks
C        192.168.23.0/30 is directly connected, GigabitEthernet0/0
L        192.168.23.2/32 is directly connected, GigabitEthernet0/0
      192.168.25.0/30 is subnetted, 1 subnets
S        192.168.25.0 [1/0] via 192.168.23.1
      192.168.27.0/30 is subnetted, 1 subnets
S        192.168.27.0 [1/0] via 192.168.23.1
      192.168.30.0/24 is variably subnetted, 2 subnets, 2 masks
C        192.168.30.0/24 is directly connected, GigabitEthernet0/1.10
L        192.168.30.1/32 is directly connected, GigabitEthernet0/1.10
S     192.168.40.0/24 [1/0] via 192.168.23.1
S     192.168.50.0/24 [1/0] via 192.168.23.1
VGW_2901_ODA#sh ip route 173.247.105.170
% Network not in table
VGW_2901_ODA#

 

Am I missing something simple?

 

Here are the 'ip route' commands.

 

ip route 0.0.0.0 0.0.0.0 192.168.3.14
ip route 192.168.1.0 255.255.255.0 192.168.23.1
ip route 192.168.4.0 255.255.255.0 192.168.23.1
ip route 192.168.5.0 255.255.255.0 192.168.23.1
ip route 192.168.10.0 255.255.255.0 192.168.23.1
ip route 192.168.21.0 255.255.255.252 192.168.23.1
ip route 192.168.25.0 255.255.255.252 192.168.23.1
ip route 192.168.27.0 255.255.255.252 192.168.23.1
ip route 192.168.40.0 255.255.255.0 192.168.23.1
ip route 192.168.50.0 255.255.255.0 192.168.23.1

 

 

Regards,
Jason

Everyone's tags (4)
1 ACCEPTED SOLUTION

Accepted Solutions

The "show ip route" command

The "show ip route" command will only show you routing table entries that have an explicit (not default) route. If you want to see where the router is sending traffic, use the "show ip cef 173.247.105.170" command instead.

2 REPLIES

The "show ip route" command

The "show ip route" command will only show you routing table entries that have an explicit (not default) route. If you want to see where the router is sending traffic, use the "show ip cef 173.247.105.170" command instead.

New Member

Thank you.

Thank you.

142
Views
0
Helpful
2
Replies