IPSec not working Cisco RV220W Router-firewall via remote access using an IPsec VPN Client
Please advice what is preventing me to establish a connection with a Cisco RV220W Router-firewall via remote access using an IPsec VPN Client on a laptop (Win 7 / Vista).
The Cisco RV220W is behind a NAT ISP Triple Play PPPoE Router. Port Forwarding TCP/UDP ports 47, 443, 500, 4500 and 1723 to the RV220W.
Tested succesfull IPsec with another router Cisco 871 no problem at all.
Got the PPTP, QuickVPN working fine !
On the RV220W to test I am using a default out of the box config / set up, no specials.
created a VPN client name/password for protocol XAUTH.
Via the Basic VPN Setup created an IKE POlicy and an enabled a VPN Policy.
On the Laptop I am using a Cisco VPN Client 5.0.07... while using the given host(my public IP) key and user credentials.
Error VPN Client/laptop the connection terminated locallly by the client error Reason 412 the remote peer is no longer responding.
The RV logs show ERROR: Could not find configuration for VPN-CLient-IP-address
On the RV220W : (Firmware Version 220.127.116.11)
WAN IP assigned by DHCP on the ISP router using a fixed private nat IP.
Multiple VLAN Subnet Table VLAN ID IP Address Subnet Mask DHCP Mode DNS Proxy Status 1 192.168.1.1 255.255.255.0 DHCP Serve Enabled
VPN Client Setting Table No. Enabled Username Password Allow User to Change Password Protocol 1 NA xnxaxmxe xpxaxsxsxwxoxrxd Disabled XAUTH
IKE Policy Table Policy Name Name-abc Direction / Type Responder Exchange Mode Aggresive Enable XAUTH Client None Local Identifier Type FQDN Identifier local.com Remote Identifier Type FQDN Identifier remote.com IKE SA Parameters Encryption Algorithm 3DES Authentication Algorithm SHA-1 Authentication Method Pre-Shared Key Pre-Shared Key Pre-Shared-Key-yyyy Diffie-Hellman (DH) Group Group 2 (1024bit ) SA-Lifetime 28800 Seconds
VPN Policy Table Policy Name Name-abc Policy Type Auto Policy Remote Endpoint FQDN remote.com NETBIOS Enable not selected Local Traffic Selection Local IP subnet Start Address 192.168.1.0 End Address Subnet Mask 255.255.255.0 Remote Traffic Selection Remote IP Any Start Address End Address Subnet Mask Split DNS Split DNS not selected Enable Domain Name Server 1 Domain Name Server 2 (Optional) Domain Name 1 Domain Name 2 (Optional) Manual Policy Parameters SPI-Incoming 0x SPI-Outgoing 0x Encryption Algorithm 3DES Key-In Key-Out Integrity Algorithm SHA-1 Key-In Key-Out Auto Policy Parameters SA-Lifetime 3600 Encryption Algorithm 3DES Integrity Algorithm SHA-1 PFS Key Group selected enable (DH) GroupGroup 2 (1024bit ) Select IKE Policy Name-abc
View Logs 2014-02-11 10:33:24: [rv220w][IKE] ERROR: Could not find configuration for VPN-CLient-IP-address 2014-02-11 10:33:29: [rv220w][IKE] ERROR: Could not find configuration for VPN-CLient-IP-address 2014-02-11 10:33:34: [rv220w][IKE] ERROR: Could not find configuration for VPN-CLient-IP-address 2014-02-11 10:33:40: [rv220w][IKE] ERROR: Could not find configuration for VPN-CLient-IP-address
IPSec not working Cisco RV220W Router-firewall via remote access
Cisco VPN Client 5.x is not supported on the RV220W. I recommend that you try a third party client such as Shrewsoft or The Greenbow (Windows) or IPSecuritas (Mac) if you wish to use something other than QuickVPN.
Hello, This article will describe how to configure PPTP VPN on the new
RV340/345 routers from the Small Business series. RV340/345
Configuration The first step is to enable the PPTP Server: Go to VPN ->
PPTP Server Change PPTP Server: from Off to On Selec...
Article ID:5748 Use TheGreenBow VPN Client to Connect with RV34x Series
Router Introduction A Virtual Private Network (VPN) connection allows
users to access, send, and receive data to and from a private network by
means of going through a public or share...
Article ID:5728 Configure a Teleworker VPN Client on the RV34x Series
Router Objective The Teleworker VPN Client feature minimizes the
configuration requirements at remote locations by allowing the device to
work as a Cisco VPN hardware client. When the T...