Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Problem with monitoring PPoE WAN connection on RV180 via SNMP

Hi,

I am trying to monitor via SNMP PPoE WAN connection on RV180.

I have two issues:

  1. When connection is disconnected (pressing disconnect button in the web interface), interface #11 disappears from SNMP.
  2. operStatus is down while connection is working

Does somebody have any ideas why it is happening? I have router of other vendor and this kind of behaviour does not happen there.

Firmware version 1.0.3.10

IF-MIB::ifAdminStatus.1 = INTEGER: up(1)

IF-MIB::ifAdminStatus.2 = INTEGER: down(2)

IF-MIB::ifAdminStatus.3 = INTEGER: down(2)

IF-MIB::ifAdminStatus.4 = INTEGER: up(1)

IF-MIB::ifAdminStatus.5 = INTEGER: up(1)

IF-MIB::ifAdminStatus.6 = INTEGER: down(2)

IF-MIB::ifAdminStatus.7 = INTEGER: down(2)

IF-MIB::ifAdminStatus.8 = INTEGER: down(2)

IF-MIB::ifAdminStatus.9 = INTEGER: up(1)

IF-MIB::ifAdminStatus.10 = INTEGER: up(1)

IF-MIB::ifAdminStatus.11 = INTEGER: up(1)

IF-MIB::ifOperStatus.1 = INTEGER: up(1)

IF-MIB::ifOperStatus.2 = INTEGER: down(2)

IF-MIB::ifOperStatus.3 = INTEGER: down(2)

IF-MIB::ifOperStatus.4 = INTEGER: up(1)

IF-MIB::ifOperStatus.5 = INTEGER: up(1)

IF-MIB::ifOperStatus.6 = INTEGER: down(2)

IF-MIB::ifOperStatus.7 = INTEGER: down(2)

IF-MIB::ifOperStatus.8 = INTEGER: down(2)

IF-MIB::ifOperStatus.9 = INTEGER: up(1)

IF-MIB::ifOperStatus.10 = INTEGER: up(1)

IF-MIB::ifOperStatus.11 = INTEGER: down(2)


Log is full of these messages:

Wed Jan 22 12:57:21 2014(GMT) [rv180][Kernel][KERNEL] [ 2605.430000] pppoe_sid_index=1

Wed Jan 22 12:57:31 2014(GMT) [rv180][Kernel][KERNEL] [ 2615.520000] pppoe_sid_index=1

Wed Jan 22 12:57:47 2014(GMT) [rv180][Kernel][KERNEL] [ 2632.680000] pppoe_sid_index=1


Wed Jan 22 12:58:55 2014(GMT) [rv180][Kernel][KERNEL] [ 2695.530000] cmd 35313 is not SIOCDEVPRIVATE(35312)

Wed Jan 22 12:58:55 2014(GMT) [rv180][Kernel][KERNEL] [ 2695.530000] cmd 35313 is not SIOCDEVPRIVATE(35312)

Wed Jan 22 12:58:55 2014(GMT) [rv180][Kernel][KERNEL] [ 2695.530000] cmd 35313 is not SIOCDEVPRIVATE(35312)

Wed Jan 22 12:27:23 2014(GMT) [rv180][Kernel][KERNEL] [  785.160000] cmd 35313 is not SIOCDEVPRIVATE(35312)

  • Small Business Routers
Everyone's tags (2)
1 REPLY
New Member

Problem with monitoring PPoE WAN connection on RV180 via SNMP

Your best bet would be to give us a call at 1-866-606-1866 and open a case so we can work on the issue a little more in depth than we could on the support forums.

459
Views
0
Helpful
1
Replies
This widget could not be displayed.