Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

RV180 IPSEC from Android

Hi,

I am getting this problem when trying to connect to ipsec vpn

 

Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] INFO:  Received attribute type "ISAKMP_CFG_REPLY" from 46.135.70.24[32684]
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] INFO:  Login succeeded for user  "admin"
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] INFO:  XAuthUser admin Logged In from IP Address 46.135.70.24 
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] INFO:  Received attribute type "ISAKMP_CFG_REQUEST" from 46.135.70.24[32684]
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] ERROR:  Local configuration for 46.135.70.24[32684] does not have mode config
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] ERROR:  Local configuration for 46.135.70.24[32684] does not have mode config
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] ERROR:  Local configuration for 46.135.70.24[32684] does not have mode config
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] ERROR:  Local configuration for 46.135.70.24[32684] does not have mode config
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] ERROR:  Local configuration for 46.135.70.24[32684] does not have mode config
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] ERROR:  Local configuration for 46.135.70.24[32684] does not have mode config
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] ERROR:  Local configuration for 46.135.70.24[32684] does not have mode config
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] ERROR:  Local configuration for 46.135.70.24[32684] does not have mode config
Thu May 08 08:10:06 2014 (GMT +0100): [routerBB9298] [IKE] WARNING:  Ignored attribute 28678
Thu May 08 08:10:09 2014 (GMT +0100): [routerBB9298] [IKE] INFO:  Sending Informational Exchange: notify payload[10381]

 

Does anyone have idea what is wrong? What means this  Local configuration for 46.135.70.24[32684] does not have mode config?

 

View:

Selected IKE Policy View
General
Policy Namexxxxxxx 
Direction / TypeBoth 
Exchange ModeAggresive 
Enable XAUTH Client  
Local Identification
Identifier TypeFQDN 
FQDNlocal.com 
Peer IKE Identification
Identifier TypeFQDN 
FQDNremote.com 
IKE SA Parameters
Encryption Algorithm3DES 
Authentication AlgorithmSHA-1 
Authentication MethodPre-Shared Key 
Pre-Shared Keyxxxxxxxx 
Diffie-Hellman (DH) GroupGroup 2 (1024bit ) 
SA-Lifetime28800 Seconds
 

 

Thank you in advance

 

Peter

 

3 REPLIES
Bronze

I found that ipsec doesn't

I found that ipsec doesn't work because the IP of the phone is always changing. Try using the PPTP option and see if that works.
 

Huntsville's Premiere Car and Bike e-magazine: www.huntsvillecarscene.com
Highlighted
New Member

Hi Samir, Yes pptp is no

Hi Samir,

 

Yes pptp is no problem. But i wanted ipsec :(

Bronze

Ipsec won't work because of

Ipsec won't work because of the IP address issue.  Sorry. :(
 

Huntsville's Premiere Car and Bike e-magazine: www.huntsvillecarscene.com
102
Views
0
Helpful
3
Replies
CreatePlease to create content