VPN Ipsec connection through 2 routers wrv210

[doneverona]

Hi,

i try to configure and open a tunnel in ipsec following the user guide but i'm not able to make it works.

I have two wrv210 in two different locations. Bth take internet connection throguh a Draytek Vigor e2700 (provide by the ISP).

Every WRV210 is connected in DHCP like Gateway and if i connect a PC or a Phone to them they gives internet connection

Every location has a static IP address

I give you the configuration

LOCATION 1

STATIC IP: 77.43.34.XXX

DRAYTEK ROUTER (ISP) ADDRESS: 10.0.0.1 / 255.255.255.0

WRV210 DHCP ADDRESS: 10.0.0.12

WRV210 LOCAL ADDRESS: 192.168.1.1 /255.255.255.0

LOCATION 2

STATIC IP: 77.43.42.XXX

DRAYTEK ROUTER (ISP) ADDRESS: 192.168.1.1 / 255.255.255.0

WRV210 DHCP ADDRESS: 192.168.1.219

WRV210 LOCAL ADDRESS: 192.168.0.1 /255.255.255.0

BOTH WRV210 HAVE FIRMWARE 2.0.0.11

IN DRAYTEK ROUTER CONFIGURATION I OPEN PORTS FOR WRV ADDRESSES FROM 0 TO 60999 BOTH TCP AND UDP

IN VPN IPSEC CONFIGURATION I GIVE THE FOLLOW INSTRUCTIONS

CONFIGURATION

KEY EXCHANGE: AUTOMATIC (IKE)

OPERATION MODE: PRINCIPAL

CRITT ISAKMP: 3DES

AUTENTIC ISAKMP: MD5

ISAKMP GROUP: GROUP 2 1024 BIT

KEY DURAITON: 3600

PFS: DISABLED

IPSEC CRITT: AUTOMATIC

KEY DURATION IPSEC: 3600

PRE-CONDIVIDED KEY: conatifranceschetti

IN ALL KIND OF CONFIGURATION I TRY TO GIVE THE TUNNEL REMAIN IN STATUS : T

AND NOT OPEN

HOW CAN I CONFIGURE AND OPEN THIS TUNNEL??

THANKS IN ADVANCE

[Ganesh Hariharan]

Hi,
i try to configure and open a tunnel in ipsec following the user guide but i'm not able to make it works.
I have two wrv210 in two different locations. Bth take internet connection throguh a Draytek Vigor e2700 (provide by the ISP).
Every WRV210 is connected in DHCP like Gateway and if i connect a PC or a Phone to them they gives internet connection
Every location has a static IP address
I give you the configuration
LOCATION 1
STATIC IP: 77.43.34.XXX
DRAYTEK ROUTER (ISP) ADDRESS: 10.0.0.1 / 255.255.255.0
WRV210 DHCP ADDRESS: 10.0.0.12
WRV210 LOCAL ADDRESS: 192.168.1.1 /255.255.255.0
LOCATION 2
STATIC IP: 77.43.42.XXX
DRAYTEK ROUTER (ISP) ADDRESS: 192.168.1.1 / 255.255.255.0
WRV210 DHCP ADDRESS: 192.168.1.219
WRV210 LOCAL ADDRESS: 192.168.0.1 /255.255.255.0
BOTH WRV210 HAVE FIRMWARE 2.0.0.11
IN DRAYTEK ROUTER CONFIGURATION I OPEN PORTS FOR WRV ADDRESSES FROM 0 TO 60999 BOTH TCP AND UDP
IN VPN IPSEC CONFIGURATION I GIVE THE FOLLOW INSTRUCTIONS
CONFIGURATION
KEY EXCHANGE: AUTOMATIC (IKE)
OPERATION MODE: PRINCIPAL
CRITT ISAKMP: 3DES
AUTENTIC ISAKMP: MD5
ISAKMP GROUP: GROUP 2 

Hi,

Check out the below link for step by step configiguration ip sec site to site configuration on routers

http://www.petri.co.il/how-to-configure-ipsec-encryption-with-cisco-ios.htm

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

[doneverona]

Sorry but the page that you send to me was not helpful. I don't comprehend how can i set my routers to create the VPN.

I hope that somkeone of Cisco Technical Assistance give me a response...

Thanks anyway ganeshh