Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

VPN Ipsec connection through 2 routers wrv210

Hi,

i try to configure and open a tunnel in ipsec following the user guide but i'm not able to make it works.

I have two wrv210 in two different locations. Bth take internet connection throguh a Draytek Vigor e2700 (provide by the ISP).

Every WRV210 is connected in DHCP like Gateway and if i connect a PC or a Phone to them they gives internet connection

Every location has a static IP address

I give you the configuration

LOCATION 1

STATIC IP: 77.43.34.XXX

DRAYTEK ROUTER (ISP) ADDRESS: 10.0.0.1 / 255.255.255.0

WRV210 DHCP ADDRESS: 10.0.0.12

WRV210 LOCAL ADDRESS: 192.168.1.1 /255.255.255.0

LOCATION 2

STATIC IP: 77.43.42.XXX

DRAYTEK ROUTER (ISP) ADDRESS: 192.168.1.1 / 255.255.255.0

WRV210 DHCP ADDRESS: 192.168.1.219

WRV210 LOCAL ADDRESS: 192.168.0.1 /255.255.255.0

BOTH WRV210 HAVE FIRMWARE 2.0.0.11

IN DRAYTEK ROUTER CONFIGURATION I OPEN PORTS FOR WRV ADDRESSES FROM 0 TO 60999 BOTH TCP AND UDP

IN VPN IPSEC CONFIGURATION I GIVE THE FOLLOW INSTRUCTIONS

CONFIGURATION

KEY EXCHANGE: AUTOMATIC (IKE)

OPERATION MODE: PRINCIPAL

CRITT ISAKMP: 3DES

AUTENTIC ISAKMP: MD5

ISAKMP GROUP: GROUP 2 1024 BIT

KEY DURAITON: 3600

PFS: DISABLED

IPSEC CRITT: AUTOMATIC

KEY DURATION IPSEC: 3600

PRE-CONDIVIDED KEY: conatifranceschetti

IN ALL KIND OF CONFIGURATION I TRY TO GIVE THE TUNNEL REMAIN IN STATUS : T

AND NOT OPEN

HOW CAN I CONFIGURE AND OPEN THIS TUNNEL??

THANKS IN ADVANCE

2 REPLIES

Re: VPN Ipsec connection through 2 routers wrv210

Hi,

i try to configure and open a tunnel in ipsec following the user guide but i'm not able to make it works.

I have two wrv210 in two different locations. Bth take internet connection throguh a Draytek Vigor e2700 (provide by the ISP).

Every WRV210 is connected in DHCP like Gateway and if i connect a PC or a Phone to them they gives internet connection

Every location has a static IP address

I give you the configuration

LOCATION 1

STATIC IP: 77.43.34.XXX

DRAYTEK ROUTER (ISP) ADDRESS: 10.0.0.1 / 255.255.255.0

WRV210 DHCP ADDRESS: 10.0.0.12

WRV210 LOCAL ADDRESS: 192.168.1.1 /255.255.255.0

LOCATION 2

STATIC IP: 77.43.42.XXX

DRAYTEK ROUTER (ISP) ADDRESS: 192.168.1.1 / 255.255.255.0

WRV210 DHCP ADDRESS: 192.168.1.219

WRV210 LOCAL ADDRESS: 192.168.0.1 /255.255.255.0

BOTH WRV210 HAVE FIRMWARE 2.0.0.11

IN DRAYTEK ROUTER CONFIGURATION I OPEN PORTS FOR WRV ADDRESSES FROM 0 TO 60999 BOTH TCP AND UDP

IN VPN IPSEC CONFIGURATION I GIVE THE FOLLOW INSTRUCTIONS

CONFIGURATION

KEY EXCHANGE: AUTOMATIC (IKE)

OPERATION MODE: PRINCIPAL

CRITT ISAKMP: 3DES

AUTENTIC ISAKMP: MD5

ISAKMP GROUP: GROUP 2

Hi,

Check out the below link for step by step configiguration ip sec site to site configuration on routers

http://www.petri.co.il/how-to-configure-ipsec-encryption-with-cisco-ios.htm

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

Community Member

Re: VPN Ipsec connection through 2 routers wrv210

Sorry but the page that you send to me was not helpful. I don't comprehend how can i set my routers to create the VPN.

I hope that somkeone of Cisco Technical Assistance give me a response...

Thanks anyway ganeshh

1014
Views
0
Helpful
2
Replies
CreatePlease to create content